answersLogoWhite

0

Hold in reset button on speedo, turn on ign then release button,then turn it to the right and release it then switch off ign. This will only work if service is due now or showing nearly due

User Avatar

Wiki User

13y ago

What else can I help you with?

Related Questions

How do you change a side light bulb on a Skoda octavia?

hi how do you change aside light bulb on a skoda octavia


How do you reset service light on dashboard for Skoda octavia 1999?

To reset the service light on a 1999 Skoda Octavia, turn the ignition key to the "On" position without starting the engine. Press the accelerator pedal three times fully within a few seconds. Then, turn off the ignition and start the engine; the service light should be reset. If it doesn’t turn off, repeat the steps to ensure they were done correctly.


How do you reset service light on Skoda octavia?

To reset the service light on a Skoda Octavia, turn on the ignition without starting the engine. Press the accelerator pedal three times within ten seconds. Turn off the ignition and then start the engine; the service light should be reset. If it doesn’t turn off, repeat the process.


How do you reset service light on dashboard for Skoda fabia?

You will find the directions in your car manual.


What is the epc light for Skoda octavia?

what does epc mean on the dash bord of a skoda ovt mean


How do you change a light fuse in a Skoda Octavia?

To change a light fuse in a Skoda Octavia, first, locate the fuse box, usually found under the dashboard or in the engine compartment. Consult the owner's manual for the specific fuse layout and identify the fuse corresponding to the light you need to replace. Use a fuse puller or pliers to remove the faulty fuse and replace it with a new one of the same amperage. Finally, test the light to ensure it is functioning properly.


How do you reset power assisted steering sensor dashboard warning light on a 2007 Skoda octavia?

To reset the power assisted steering sensor warning light on a 2007 Skoda Octavia, first ensure that the steering system is functioning correctly. Then, turn off the ignition and disconnect the battery for about 10-15 minutes. Reconnect the battery, start the vehicle, and check if the warning light has cleared. If the light persists, it may indicate a more serious issue needing professional diagnosis.


How do you reset the service light on Skoda superb?

To reset the service light on a Skoda Superb, turn on the ignition without starting the engine. Use the trip reset button on the dashboard to navigate to the service menu. Once there, press and hold the reset button until the service interval is reset. Finally, turn off the ignition and then restart the car to ensure the service light is off.


What is the orange warning light on a Skoda octavia?

the orange oil or fuel warning light normally indicates a filter wants changing


How do you change a stop light on a Skoda Octavia?

To change a stop light on a Skoda Octavia, first, open the trunk and locate the tail light assembly. Remove any screws or clips securing the assembly, then carefully pull it out. Disconnect the electrical connector and remove the old bulb by twisting it counterclockwise. Insert the new bulb, reconnect the electrical connector, and reassemble the tail light assembly.


How do i turn off the front parking sensor on Skoda octavia?

To turn off the front parking sensor on a Skoda Octavia, locate the parking sensor button, usually found on the center console or dashboard. Press the button to deactivate the sensors; a light on the button may indicate that the sensors are off. If your model has an infotainment system, you may also find the option to disable the sensors in the settings menu. Refer to the owner's manual for specific instructions related to your model year.


How do you replace the rear light cover on a Skoda octavia?

To replace the rear light cover on a Skoda Octavia, first, open the trunk and locate the access panel or screws holding the light assembly in place. Remove any screws or clips, then gently pull the light assembly away from the body. Disconnect the wiring harness, replace the old cover with the new one, reconnect the harness, and reassemble the light by securing it back with screws or clips. Finally, test the light to ensure it’s functioning correctly.