0
To reset the service indicator on a 2000 BMW Z3 after an oil change, first turn the ignition key to the "ON" position without starting the engine. Then, press the gas pedal fully three times within five seconds. Afterward, turn the ignition off, and when you turn it back on, the service indicator should be reset. If it doesn't reset, you may need to repeat the steps or check for any additional issues.
What else can I help you with?
How do you Reset service indicator on 2000 ml320?
To reset the service indicator on a 2000 Mercedes-Benz ML320, turn the ignition key to the "ON" position without starting the engine. Press the gas pedal three times within five seconds. After doing this, turn the ignition off and then back on to verify that the service indicator has been reset. If the indicator still shows, repeat the process.
Reset oil indicator 2000 BMW 323i?
The reset oil indicator on a 2000 BMW 323i warns the driver that it is time to service the engine. It is automatically set to trigger every 3,000 miles and can be reset once the oil has been changed.
How do you reset the performing service light indicator on a 2000 Jeep Cherokee?
Key on, close doors. Press "step" until "0 miles to service" is displayed. Press and hold "reset".
How do you reset service indicator message for 2000 Mercedes Bens E240 after b is complete?
Most likely the same as the 2000 E430 which is as follows: turn key to position 1 press up or down arrow til service indicator appears press and hold (R) button for approx 2 seconds display will show "do you want to reset service interval?" press (R) button again to reset Hope that works for you.
How do you turn off the perform service light on a 2000 jeep grand Cherokee?
you reset it by hitting step until you see "miles remaining to service" then you hold reset button and it will change to 3000
Reset service engine soon light on 2000 Nissan?
How does one reset service engine light on 2000 Nissan Quest Thanks Bill
How do you reset service light on ml 320 mercedes 2000?
I did the oil change on my 2000 ml 320 but the dash still displaying -10 D and i have tried to do the reset following the procedurs but the two little wrenches are there and
How do you reset wrench on 2000 500s?
To reset the wrench indicator on a 2000 Fiat 500, turn the ignition key to the "ON" position without starting the engine. Press the gas pedal three times within 10 seconds. After releasing the pedal, the wrench indicator should turn off, indicating that the maintenance reminder has been reset. If the indicator remains on, repeat the process.
How do you reset the air bag indicator light on a 2000 Ford Expedition?
abdulla breikachi is fat
Reset brake lamp indicator 2000 Acura TL?
To reset the brake lamp indicator on a 2000 Acura TL, first ensure that the brake lights are functioning properly. If they are, disconnect the negative terminal of the battery for about 10 minutes to reset the system. Reconnect the battery and check if the indicator has cleared. If the light remains on, it may indicate a more serious issue that requires further diagnosis.
How do you reset the service indicator on a vw transporter?
To reset a T4 Service indicator. With ign off, press and hold trip mtr butto. Switch ign on and release the button. If only "insp"is in the display, turn minutes knob to right on the clock, "service ----" should now appear in the display. Turn off ign and service is reset. If "insp and Oil" are shown in the display, get to insp by toggling the trip mtr button. follow above procedure, but don't yet turn off the ign, press the trip mtr button again and "oil" should appear, again turn the minutes knob to the right and "service----" will appear. Turn ign off and service is reset. Works for me on my 2000 T4.
How do you reset the service indicator on a Transporter?
To reset a T4 Service indicator. With ign off, press and hold trip mtr butto. Switch ign on and release the button. If only "insp"is in the display, turn minutes knob to right on the clock, "service ----" should now appear in the display. Turn off ign and service is reset. If "insp and Oil" are shown in the display, get to insp by toggling the trip mtr button. follow above procedure, but don't yet turn off the ign, press the trip mtr button again and "oil" should appear, again turn the minutes knob to the right and "service----" will appear. Turn ign off and service is reset. Works for me on my 2000 T4.
