answersLogoWhite

0

Removal Disconnect the battery ground cable. Raise and support the vehicle. Remove the dual converter Y-pipe. Remove the starter motor. Remove the engine rear plate. Drain the engine oil. Remove the 16 oil pan bolts. Remove the oil pan. Remove the oil pan gasket. Installation Apply a bead of Silicone Gasket and Sealant in two places where the cylinder block meets the front cover and in two places where the rear main bearing cap meets the cylinder block. CAUTION: Correct alignment of the oil pan is critical. Position the oil pan gasket. Position the oil pan and install the 16 bolts. Tighten the bolts in three stages: Stage 1: Tighten the four corner bolts to 12 Nm (9 lb-ft). Stage 2: Tighten the remaining bolts from back to front to 12 Nm (9 lb-ft). Stage 3: Check all bolts for correct tightness. Install the engine rear plate. Install the starter motor. Install the dual converter Y-pipe. Lower the vehicle. Fill the engine with 5W-30 Motor Oil. Connect the battery ground cable. NOTE: The cooling fan should cycle at least one time. Start the engine and allow it to reach normal operating temperature. Stop the engine. Raise and support the vehicle. Retighten the oil pan bolts from the back to front to 12 Nm (9 lb-ft). Inspect the oil pan gasket for correct alignment. Lower the vehicle.

User Avatar

Wiki User

19y ago

What else can I help you with?

Related Questions

How do you change the head gaskets on a 2000 silverado?

Remove the valve cover. Unbolt the head and remove it. Take the old gasket off and clean the gasket surface. Apply the new gasket and reverse the process.


How do you change the oil pan gasket on a 2000 Chevy Impala?

Drain the oil from your 2000 Chevy Impala oil pan. Remove the oil pan retaining bolts. Remove the old oil pan gasket and clean the surface. Put the new oil pan gasket on and reverse the process.


How do you change oil pan gasket on 2000 S-10?

You can change the oil pan gasket in your 2000 Chevrolet S 10 pickup truck by removing the oil pan bolts. Once the bolts are removed the oil pan will come off. Remove the old oil pan gasket and replace it with a new gasket.


How do you Remove and Replace the IAC valve on a 2000 Taurus?

AnswerThe valve is held in place by two bolts. Remove them and disconnect the electrical connector. Use a new gasket and install the new valve. Connect the wires. Rick


How do you change sump gasket on ford transit 100 2.5 2000 model?

Drain off the oil first, then remove the sump bolts. Hey presto, The gasket it there, remove and refit new one, or bodge it with silicone sealant.


How do you fix intake gasket on 2000 lasabre?

The only fix for a bad intake gasket is to remove the intake manifold and replace the gasket.


How much does it cost to replace a timing cover gasket on a Mercury Sable 2001?

I just had the timing cover gasket on my 2000 Ford Taurus replaced...Cost of Repair was $513


How do you change the manifold gasket on a 2000 daewoo matiz?

To change the manifold gasket on a 2000 Daewoo Matiz, first disconnect the battery and remove any components obstructing access to the manifold, such as the air intake and exhaust components. Then, unbolt the manifold from the engine, carefully remove the old gasket, and clean the surfaces to ensure a proper seal. Place the new gasket in position, reattach the manifold, and tighten the bolts to the manufacturer's specifications before reassembling any removed components. Finally, reconnect the battery and start the engine to check for leaks.


How do you remove valve cover gasket on a 2000 Cadillac DeVille?

remove right valve cover on cadilac sts


How do you change rear spark plugs on 2000 Taurus ffv?

Remove the upper intake. Don't try and go from underneath like I did. Took forever and couldn't get the wires on properly.


How do you change the power steering filter on a 2000 Taurus?

There is no power steering filter


How do you remove the console from a 2000 Taurus SEL?

There are screws that hold it on. Sometimes they are located under the compartment.