0
Obviously the positive one....which is best found by being the one that DOESN'T end at a ground point. the easiest solution to that is to start from the starter. the LARGEST (presumibly black) wire from the starter to the battery terminal is the GROUND. that would make the other terminal the positive.
What else can I help you with?
Where do cables to jumpstart 1975 Mercedes 450sl go?
To jumpstart a 1975 Mercedes 450SL, connect the positive (red) cable to the positive terminal of the dead battery and the other end to the positive terminal of the working battery. Then, connect the negative (black) cable to the negative terminal of the working battery and attach the other end to a grounded metal surface on the engine block or chassis of the 450SL, away from the battery. This setup helps prevent sparks near the dead battery. Finally, start the working vehicle, then the Mercedes.
How do you run your power wire at battery with oldmobile alero 99?
Red, positive + cable to Positive + battery terminal. Black, negative - cable to Negative - battery terminal.
How do you replace the positive battery cable on a 1996 Ford Aspire?
To replace the positive battery cable on a 1996 Ford Aspire, first disconnect the negative battery terminal to ensure safety. Then, remove the bolt securing the positive cable to the battery terminal and detach the cable. Install the new positive cable by connecting it to the battery terminal and tightening the bolt securely. Finally, reconnect the negative terminal to complete the process.
Where are jump start terminals Mercedes elegance?
The battery post positive terminal is where you connect the positive cable. Connect the negative cable to anyplace on the engine or chassis. Connect positive first and remove it last.
How do you change the positive battery cable on 2001 Toyota Sequoia?
To change the positive battery cable on a 2001 Toyota Sequoia, first, ensure the vehicle is turned off and the keys are removed. Disconnect the negative battery terminal to prevent any short circuits. Then, remove the bolt securing the positive battery cable to the battery terminal using a wrench, and lift the cable off. Finally, attach the new positive battery cable by securing it to the battery terminal with the bolt, and reconnect the negative terminal.
Replace positive battery terminal cable?
From battery to starter solenoid
How connect Mercedes 608d van 1981 to battery?
To connect the battery in a 1981 Mercedes 608D van, first ensure the vehicle is turned off. Identify the positive (+) and negative (-) terminals on the battery and clean any corrosion if present. Connect the positive terminal first by attaching the red cable to the positive terminal, followed by the black cable to the negative terminal. Once securely connected, ensure the connections are tight and free of any debris before starting the vehicle.
What is the proper battery cable connection when jumping two automotive batteries?
When jumping two automotive batteries, connect the positive () cable to the positive terminal of the dead battery and the other end to the positive terminal of the live battery. Then, connect the negative (-) cable to the negative terminal of the live battery and the other end to a metal surface on the car with the dead battery, away from the battery.
What battery cable goes to the positive terminal?
It is usually red.
95 T100 has an added cable from the positive battery terminal to chassis When the cable broke it drained the battery any info will help also the negative Battery terminal is to chassis.?
There is no way that the positive battery terminal was ever connected to the chassis. This would be a dead short and would fry the battery. Negative to chassis is correct, but positive to chassis, no way. That positive cable goes somewhere else.
How do you jump a 1999 Clk 320 Mercedes when you cant get to he battery in the trunk?
To jump a 1999 CLK 320 Mercedes when you can't access the battery in the trunk, locate the auxiliary jump start terminal under the hood, usually near the driver's side. Use a set of jumper cables, connecting the red cable to the positive terminal on the jump start terminal and the other end to the positive terminal of the donor battery. Connect the black cable to the donor battery's negative terminal, and then attach the other end to a solid ground point on the engine block or chassis of your car. Start the donor vehicle, then attempt to start your Mercedes.
How do you jump start a 1997 mercedes 500sl?
To jump start a 1997 Mercedes 500SL, first ensure both vehicles are turned off. Connect the red jumper cable to the positive terminal of the dead battery and the other end to the positive terminal of the working battery. Then, connect the black jumper cable to the negative terminal of the working battery and attach the other end to a grounded metal surface on the dead vehicle, away from the battery. Start the working vehicle, let it run for a few minutes, and then attempt to start the 500SL.
