answersLogoWhite

0

http://en.allexperts.com/q/Motorcycle-Repair-837/1985-Honda-Shadow-Clutch.htm

User Avatar

Wiki User

17y ago

What else can I help you with?

Related Questions

How do you bleed the clutch on a Honda Shadow VT1100 motorcycle?

Same as for the brakes. Locate the bleeder, slack it and re tighten. Have someone pull in the clutch and hold, you release the bleeder, then tighten it while the clutch is still held in. Once the bleeder is tight, release the clutch and repeat till all the air is out. Make sure to refill the fluid.


Ford f150 if clutch is bad will trans still shift into gear or is that an indicator of another problem?

the trans will still shift into gear with a bad clutch you will find tho, sometimes this will not happen. usaully it is NOT indicative of other problems.


Your clutch may be going out how do you know for sure?

You have to look at the wear on the clutch and look for cracks. If the clutch does go out, the shifter will still move everywhere, but the transmission will not shift.


Chevrolet discontinued clutch pedal for 1983 s10 what replaced it?

Not sure what you're asking about. I have a 1998 S10 standard shift that still has a clutch pedal.


I try to shift gears on my Volkswagen golf with a clutch but it just grinds why?

try to make sure the clutch pedal is all the way down before you change gear. in no way shape or form should you have to floor the clutch everytime you shift gears, however, if you are still grinding gears while flooring the clutch, and if there isn't that little bit of give on the pedal i'd suggest adjusting or replacing the clutch.


How do you adjust shift linkage on 95 Chevy cavalier?

92 cavalier 31 clutch has to be on floor and still shifts hard


Can a car still drive without the clutch?

With a little practice you can start a vehicle in 1st gear and shift gears without the use of a clutch. This would be only to get you safely home or to a garage.


What causes a stick shift car to shut off?

Hold down the clutch when sitting still or going too slow for that gear.


91 Honda CRX will not shift into first gear I believe that the synchronizer is bad.?

Check the hydraulic fluid level for the clutch master cylinder, it may be empty. If it is empty you can fill it with DOT 3 brake fluid. This may temporarily fix the problem but you still have a leak in the system.


Installed a new cluth on a ford ranger have bled the hydraulic system completely 3X and the clutch is still not fully engaging also replaced the slave cylinder?

Let's agree on terms. Clutch is still not fully engaging? To me this means that when it's in gear the clutch slips. Looking at it another way I wonder if you mean when you step on the clutch it doesn't disengage. That it is hard to shift gears. Makes a difference. If the clutch is not gripping that is not going to have anything to do with the slave cylinder or bleeding it. If it is that the clutch is not disengaging so that you can shift you are sure about your bleeding technique, changed the slave, the only things left are the master cylinder and the lines.


Why wont my 97 Kawasaki ninja 500 shift from first at a dead stop?

Your 1997 Kawasaki Ninja 500 might not shift from first gear at a dead stop due to several potential issues. Common causes include a faulty clutch that isn't fully disengaging, an issue with the shift lever mechanism, or old, contaminated transmission fluid. Additionally, if the bike is in gear with the clutch pulled in but still won't shift, it could indicate problems with the shift linkage or internal transmission components. It's best to check the clutch operation and inspect the shift mechanism for any obstructions or wear.


I have bled the slave cylinder on my 240sx and replaced the clutch master cylinder and my 240sx will still not shift into gear. What else can I check?

If you did not bench bleed the master, you need to do that.