0
To bleed or replace the slave cylinder on a 1989 Ford F-150 4x4, first, ensure the vehicle is securely lifted and supported. If replacing, disconnect the hydraulic line from the slave cylinder and remove the mounting bolts to take it out. To bleed the new or existing slave cylinder, fill the clutch master cylinder with fluid, then have someone press the clutch pedal while you open the bleeder valve on the slave cylinder, allowing air and old fluid to escape. Close the valve before the pedal is released, and repeat until no air bubbles appear.
What else can I help you with?
How do you replace the clutch slave cylinder on a 1989 Jeep Wrangler?
How do you replace the clutch slave cylinder on a 1989 jeep wrangler
How do you replace 1989 jeep Comanche clutch slave cylinder?
Remove the transmission to excess the inturnal slave cylinder
How do you bleed a clutch master and slave cylinder on an 1989 Chevy?
It is important to bleed a clutch master and slave cylinder to make sure all of the air is out of the lines. For a 1989 Chevy you would need to know model you had, and then find the repair manual for that specific vehicle.
How do you replace slave cylinder on 1989 ford f150 4x4?
You Must remove the trans to access the slave... on the 5 speed for sure.
Where can you find the Clutch slave Cylinder on a 1989 Nissan Pathfinder?
The Clutch slave cylinder is located on the passenger side of the bellhousing.I recommend to replace the Clutch Master cylinder also;if either one is replaced , the other will fail in no time.
Where do you bleed the clutch on a 1989 Honda Prelude?
You will find the bleeder valve on the Slave Cylinder, which is mounted on the front of the transmission, by the radiator. You will find it in the front and center of the engine compartment.
How do you adjust a hydraulic clutch on a 1989 jeep--- what i mean is you have to push the clutch all the way to the floor to change gears. is there air in the line is there a way to bleed the line?
hydraulic clutch does not have adjustment. replace the clutch it has a slave cylinder underneath and what you do is pump up the clutch and then hold it and have somone turn the line going itno th slave cylinder until you have clear fluid that is not how you bleed a clutch to the jeep owner, if you know how to bleed brakes on a vehicle, then you know how to bleed the clutch on a vehicle both done the same way.now if no parts of the clutch, such as master or slave cylander have been touched or let run out of fluid, there is still no need to bleed as that will not be the problem you might look at the linkage on the slave cylander. sometimes there is nylon bushing on the cylander rod that wears out. replace this bushing which is easy to do and your clutch will be good again.
How do you replace a master cylinder in a 1989 Winnebago superchief?
Ho do you replace a master cylinder in a 1989 Winnebago Superchief?
How do you adjust the slave cylinder on a 1989 Chevy pickup 1500?
There is NO adjustment, You must replace the clutch set to bring the pedal back to the right position. You also need to make sure the clutch slave cylinder/ master cylinder is good before replacing clutch assy.
How do you bleed a hydraulic slave cylinder in a 1989 Toyota 4 runner?
They are all pretty much the same, there is a bleeder relief on the slave, have someone pump and hold the master, you release pressure at the slave then tighten again ( make sure they keep pressure on the pedal ) then repeat until no more air comes out, if the fluid is dirty keep going until it runs clean, you will need to keep adding fresh fluid at the master as you go, dont let it run out or you have to start all over again.
How do you fix a slave cylinder on a 1989 Jeep Wrangler?
if slave cylander is bad, it must be replaced to fix it
What if your clutch pedal isn't working until you pushe it more than halfway in and its hard to downshift 1989 Honda prelude 2.0?
answerchange master cylinder and slave properly then bleed the system properly.
