To lower the I2R losses
no
It has coils of wire wound around a metal core or frame. The amount of coiled wire depends on what voltages are to be increased or reduced (or 'transformed'). also known as the "turns ratio". The physical size is generally determined by what amount of voltage and current it is intended for. It can be open, or be enclosed in a metal can. It can be air, water or oil cooled.
Suppurters supported Katniss by bringing her some medicine for her wound. She covered the wound with it and the next morning it was clearly almost gone. Katniss used the same thing on Gale when his leg was cut.
Only a Prime can kill an original Prime. Also Optimus was fighting three Decepticons. He turned his head to see where Sam was and Megatron put his blade right through his Spark and then shot him in the wound.
she doesn't "leach" peeatas wound she washes it out then puts the medicine she got for her burns on his wound
no
The most contributing factor to core losses in transformers is the material on which they are wound. Transformers wound on iron cores are roughly 75% efficient but they can transfer large amounts of power at low frequency. Transformers wound on ferrite are typically better then 90% efficient but can't be used to transfer the same amount of power unless the frequency is increased. Switch mode power supplies do this. After that, the voltage, impedance and current are all related. If you increase the current (by increasing the voltage) there are more losses because the magnetic field strength is not directly proportional to the current. The impedance remains the same for the same number of turns. Transformers are wound to the best compromise between efficiency and transfer capability. If you try to increase the voltage too much, the core will saturate and behave like a straight piece of wire.
The Dna comprised chromosomes are wound around protein Histone Cores that are then in turn wound into a ten nanometer diameter strand that is then, in turn, wound into a thirty nanometer diameter strand - hense constriction.
Its a circular wound moist all around and at a closer look you will notice movements within the wound. The diameter of the wound will gradually enlarge. The worms can also be visible within the wound.
It means you are likely to have a wound infection and should seek medical advice asap
Some of the basic steps in wound care include: cleaning the wound (warm water works well), applying an antibiotic cream or salve on the wound and then applying a bandage to cover it. If it is a large or serious wound, you may want to see your doctor.
The spring index is the ratio (C) of the coil diameter (D) to wire diameter (d), such that C = D/d. A tightly wound spring (where a relatively large wire diameter is wound around a relatively small diameter mandrel) will have a low spring index. Note: The spring index (C) should not be confused with the spring rate, which is the ratio (k) of the force (F) to displacement (x), such that k = F/x.
you should ask a doctor or plastic surgenAnswer:If you have a large wound that has not healed for 8 weeks, it's considered to be a chronic, non-healing wound. It's best to go to a local wound care center, NJ and get the proper treatment as soon as possible. There may be reasons for slow wound healing and a doctor will be able to pinpoint these causes and administer the right treatment.
To find the length of the rope wound around the cylinder, calculate the circumference of the pipe first. The circumference ( C ) is given by the formula ( C = \pi \times d ), where ( d ) is the diameter. For a pipe with a diameter of 600 mm, the circumference is approximately ( C = \pi \times 600 \approx 1884.96 ) mm. Since the rope is wound around the pipe 18 times, the total length of the rope is ( 18 \times 1884.96 \approx 33,999.28 ) mm, or about 34 meters.
yes, if the wound is large, hold pressure until you can get assistance!
To promote healing and prevent infection when using wound care pads, it is important to follow these best practices: Clean the wound area before applying the pad. Change the pad regularly to keep the wound clean and dry. Use pads that are appropriate for the size and type of wound. Avoid using pads that are too small or too large for the wound. Consult a healthcare professional for guidance on proper wound care techniques.
To calculate the outside diameter of a steel coil, you first need to determine the inside diameter (ID) and the thickness of the steel material. The outside diameter (OD) can then be calculated using the formula: OD = ID + 2 × thickness. If the coil is wound in layers, you may also need to account for the number of layers by adding the thickness multiplied by the number of layers to the ID.