answersLogoWhite

0

When you cross them over from one another

User Avatar

Anonymous

4y ago

What else can I help you with?

Related Questions

On a 2002 buick century 3100 Do you have to take the push rods out to change the lower intake manifold gaskets and if so what is the torque spec for the rocker arms?

You will have to remove the pushrods, and there are two ways to do it. Lisle makes a pushrod tool specifically for 3100 and 3400 gm engines which tips the rockers far enough away from the pushrods so they can be removed, or you can just loosen the rockers up enough until the pushrods are able to come out. I would recommend buying the tool and removing the pushrods that way though because otherwise you will have to loosen and retighten the rocker bolts which have a few different torque specifications. They have revised their specs on rocker torque i think a couple of times, and i have seen a lot of rockers which people have pulled the threads right out when tightening the rockers too hard so if you do take the rockers off, i would take a 3/8 ratchet and get it good and snug. Do not reef on it just get it good and snug. The tool is neat though because it acts as a lever and pulls on the bottom side of the rocker on one side and pushes on the top of the other side and you can pull the pushrods right out and then you don't have to worry about anything. The tool is inexpensive too, maybe 15-20 dollars i think. I hope this information helps You will have to remove the pushrods, and there are two ways to do it. Lisle makes a pushrod tool specifically for 3100 and 3400 gm engines which tips the rockers far enough away from the pushrods so they can be removed, or you can just loosen the rockers up enough until the pushrods are able to come out. I would recommend buying the tool and removing the pushrods that way though because otherwise you will have to loosen and retighten the rocker bolts which have a few different torque specifications. They have revised their specs on rocker torque i think a couple of times, and i have seen a lot of rockers which people have pulled the threads right out when tightening the rockers too hard so if you do take the rockers off, i would take a 3/8 ratchet and get it good and snug. Do not reef on it just get it good and snug. The tool is neat though because it acts as a lever and pulls on the bottom side of the rocker on one side and pushes on the top of the other side and you can pull the pushrods right out and then you don't have to worry about anything. The tool is inexpensive too, maybe 15-20 dollars i think. I hope this information helps You will have to remove the pushrods, and there are two ways to do it. Lisle makes a pushrod tool specifically for 3100 and 3400 gm engines which tips the rockers far enough away from the pushrods so they can be removed, or you can just loosen the rockers up enough until the pushrods are able to come out. I would recommend buying the tool and removing the pushrods that way though because otherwise you will have to loosen and retighten the rocker bolts which have a few different torque specifications. They have revised their specs on rocker torque i think a couple of times, and i have seen a lot of rockers which people have pulled the threads right out when tightening the rockers too hard so if you do take the rockers off, i would take a 3/8 ratchet and get it good and snug. Do not reef on it just get it good and snug. The tool is neat though because it acts as a lever and pulls on the bottom side of the rocker on one side and pushes on the top of the other side and you can pull the pushrods right out and then you don't have to worry about anything. The tool is inexpensive too, maybe 15-20 dollars i think. I hope this information helps You will have to remove the pushrods, and there are two ways to do it. Lisle makes a pushrod tool specifically for 3100 and 3400 gm engines which tips the rockers far enough away from the pushrods so they can be removed, or you can just loosen the rockers up enough until the pushrods are able to come out. I would recommend buying the tool and removing the pushrods that way though because otherwise you will have to loosen and retighten the rocker bolts which have a few different torque specifications. They have revised their specs on rocker torque i think a couple of times, and i have seen a lot of rockers which people have pulled the threads right out when tightening the rockers too hard so if you do take the rockers off, i would take a 3/8 ratchet and get it good and snug. Do not reef on it just get it good and snug. The tool is neat though because it acts as a lever and pulls on the bottom side of the rocker on one side and pushes on the top of the other side and you can pull the pushrods right out and then you don't have to worry about anything. The tool is inexpensive too, maybe 15-20 dollars i think. I hope this information helps


What does NO WAYS IT WAYS represent?

No ---two ways AROUND it No two ways about it


Your car has two diffent sizes pushrods they were mix up so how do you know where they will go you have a 3100 engine?

They will have to be measured and cross referenced by the engine specifications. There is no other way to know what goes where.


Why does your urine come out in two streams?

it shouldn't, get it checked out


What is five minus two?

3 ...... last I checked


What are two ways to reproduce?

Two ways are sexual and asexual.


Can a woman get aids from another woman when neither women have aids?

No not if neither of you have aids. You two should get checked for aids so you two dont feel uncomfortable. Just be careful and always have your partner get checked first and you should get checked frequently for STD's as well.


What could be wrong with turn signal if everything has been checked and they still dont workwhen i say everything i checked fuzes..bulbs..relay was changed under dash my four ways and breaks work?

Only thing left is two things: 1. Turn signal switch 2. Wiring between switch and fuses.


What Comparatives are formed in what two ways?

Comparatives are formed in what two ways?


What two ways do force work?

what two ways do forces work?


What two ways are mixtures classified?

The two ways are: Heterogeneous Homogeneous


What are two ways to make a trapezoid?

What are two ways to make a trapezoid