0
Its kind of joints pipe (branch) to the primairly pipe causing blockege due to cold weather (frozen) or due to debris and sluges accumalations
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
Why are sponges considered to be an evolutionary dead end?
No other animals are believed to have evolved from sponges, thus they win the title of "an evolutionary dead end."
How do you make a cannon?
You have to take a sturdy piece of pipe that is not rusted and seal one end so that the force has to go out one end. you need a small touch holw so that you can ignight the powder. and in a sense you have created a cannon
What is the resonant frequency of an organ pipe related to?
Pipe lengh. a 32' pipe CCCC would produce a ferquency of about 16hz. a 64' pipe CCCCC, 8hz similarly a 16' CCC, 32hz.
How do you Prime a well water system?
If you are using a jet pump you must have a good foot valve, then remove the prime nut or gauge from the top of the pump and fill the pump and pipe with water. You may have to do this a number of times to get all the air out of the system.
What stronge ss pipe or black pipe?
Carbon Steel pipe is stronger than stainless steel pipe as there is more iron in the carbon steel. However, the application depends on the purpose the pipe is being installed. Stainless is of course capable of being sanitized and therefore can be used for food and pharmaceutical uses. Carbon Steel (black pipe) is stronger and cheaper but not sanitary.
How do you test a perforated pipe?
Not with air! Run water in pipe at highest elevation of pipe and see that water drains at end of pipe system.
Difference between bell spigot end pipe and socket end pipe?
The Spigot end is the ends that goes into the socket end of the pipe
Definition of end correction in pipe?
end correction in pipe along of the because it is not maximum in the exist of pipe
What is invert in drainage system?
The invert is the exact elevation of a drainage facility or pipe where the water is designed to flow. If a 2 foot dia. pipe crosses the road, one end of the pipe will be higher than the other, say 6 inches of fall. Say the high end (elevation measured at the end of the pipe at the flowline) is at elev. 325.00 The elev of the low end at the end flowline would be 324.50. 325.00 is the invert in 324.50 is the invert out
How can I stop steam radiator from banging?
It depends on the type of system you have. 1 pipe in, or 1 pipe in and 1 pipe out. Single pipe in/out, try replacing the relief valve or simply shimming the end of the radiator opposite where the pipe comes in. This lets water bleed out of the radiator and stops the klanging.
What is use of pipe nipple?
Pipe nipple is use as connector to both pipe which have female end. It does not same as pipe reducer which nipple has same diameter throughout both end and threaded. Pipe reducer has different diameter for both end and it is use to join different pipe diameter.
What is the of a vent pipe in a plumbing systeam is to?
I don't quite get what you mean. -A vent pipe in a plumbing system is usually 1 1/2 inch ABS pipe and may extend through the roof, or may end in a AAV under a countertop.
What is meant by fitting allowance?
The fitting allowance is the difference: (pipe end to fitting center measurement) minus (pipe end to end measurement). It is the amount of length the fitting adds to the end of the pipe (to get the center of the turn).
15km pipeline is corrosion protected with Impressed Current cathodic protection at both end of pipeline 10metres of pipe is above ground. Will the CP system work on this above ground pipe?
Yes it will
One disadvantage of using a one pipe heating system is that what?
One disadvantage of using a one pipe heating system is that what?
What is a pipe threader used for?
To form threads on the end of a piece of pipe.
What copper tube is available when using the grooved method of joining?
Grooved method? Threads on the end of the pipe? There is no tube or pipe in copper with threads. You can end a copper pipe with a connection that is threaded to accept steel pipe.
