answersLogoWhite

0

What else can I help you with?

Continue Learning about General Science

Is a screw an example of a ramp?

No a ramp is an inclined plane while a screw is an inclined plane spinning in a spiral around a rod; the two are considered different simple machines but in a sense u could say they are the same


Why do logos of pharmacies have snakes on them?

there are two symbols associated with medicine with snakes on them. 1: rod of Asclepius: it is a pole with a single snake wrapped around it. it is a ancient greek symbol associated with astrology and with healing the sick through medicine. 2: Caduceus: it is a pole with wings at the top with two snakes wrapped around it. It is the wand of Hermes. although this is historically incorrect it is believed to have become associated with medicine because of its link with alchemy (hermes being the god of alchemy).


Decscribe the structure of an electromagnet?

Okay - it's going to be difficult to do an accurate diagram on here - so bear with me...An electromagnet consists basically of a piece of metal surrounded by a coil of wire, which is connected to a power source. The simplest form would be an iron rod which has a piece of wire wrapped around it (about ten) coils should do it. The ends of the wire are attached to a 9 volt battery.Ignore the dots in the following diagram - they're just to stop the spaces being removed by the forum !...____|+ -|____| ................... || ................... ||___/\/\/\____|It's a bit crude - but I think it's understandable. Basically, you connect the battery (+ -) with a continuous piece of wire. Wrap the wire around an iron rod - the '/\/\/\'. This induces a current in the rod, while the power is connected. Snakester1962 (Supervisor)


How can an electromagnet be made stronger?

An electromagnet can be made stronger by: - A bigger iron rod. - A bigger battery/more batteries - More coils around the iron rod. - A bigger magnet. - Increase the current flowing through the coil. - Put in a soft iron core.


If an air bubble was trapped in a metal rod would it affect the rod's density?

Yes, the overall density would be less than if the rod were pure metal.

Related Questions

What is a modified version of a inclined plane?

It is a screw. A screw is an inclined plane wrapped around a rod


Which inclined plane wrapped round a rod?

The inclined plane wrapped around a rod is known as a screw. It is a simple machine that converts rotational motion into linear motion. By rotating the screw, objects can be moved up or down along its length.


What is wrapped around a screws rod?

The part of a screw that is wrapped around the central shaft of the screw is normally called a thread. It can be described technically as an inclined plane.


What do you call an inclined plane that wraps around a spiral rod?

This is a simple machine called a screw.


What type of simple machine is a scirroes?

A screw is a simple machine that is used to fasten objects together or to lift objects by rotating through a threaded shaft. It is classified as an inclined plane wrapped around a central rod.


Is a screw an example of a ramp?

No a ramp is an inclined plane while a screw is an inclined plane spinning in a spiral around a rod; the two are considered different simple machines but in a sense u could say they are the same


Is a nail a inclined plane?

No, a nail is not an inclined plane. It is a slim, pointed metal rod that is used to fasten things together by being hammered into a surface. An inclined plane is a flat surface that is tilted at an angle, used to make it easier to move objects up or down.


What kind of simple machine is a nut and bolt?

They are types of screws which are actually inclined planes that curve around the outside of a rod and the interior of a cylinder. Instead of anchoring into a surface, a bolt passes through a hole and is locked in place by the nut. At its most basic, it is an inclined plane. That inclined plane formed by the threads of the bolt is wrapped around an axle and the nut provides a mechanical advantage by being a lever (The force arm is the nut's radius). The lever can be extended (a wrench) to provide greater mechanical advantage.


Is it true that the wheel and axle are made from two or more inclined plane?

Yes, the wheel and axle can be seen as a type of simple machine that consists of two or more inclined planes. The wheel is essentially a circular inclined plane, while the axle acts as the connecting rod that the wheel rotates around. Together, they work in unison to facilitate movement and create mechanical advantage.


What kind of simple machine is nut and bolt?

They are types of screws which are actually inclined planes that curve around the outside of a rod and the interior of a cylinder. Instead of anchoring into a surface, a bolt passes through a hole and is locked in place by the nut. At its most basic, it is an inclined plane. That inclined plane formed by the threads of the bolt is wrapped around an axle and the nut provides a mechanical advantage by being a lever (The force arm is the nut's radius). The lever can be extended (a wrench) to provide greater mechanical advantage.


What is a screw made up of wrapped around a post or rod?

A screw is a threaded fastener that is made up of a helical ridge wrapped around a cylindrical post or rod. The threads on the screw allow it to be rotated and driven into a material, providing a secure hold.


What are the 6 rube goldbergs machines?

Simplest form: The Lever is a basic machine that amplifies force. Inclined Plane: A slanted surface used to raise or lower objects. Wheel and Axle: Consists of a wheel attached to a rod, allowing for better movement. Pulley: A wheel with a groove that a rope or cable can run through to lift heavy objects. Wedge: A tool with a sharp edge used for splitting or lifting objects. Screw: An inclined plane wrapped around a cylinder, used to hold objects together or lift loads when turned.