This boardis similar in composition to Type X drywall,
except that it has more glass fibers,
and, it has another ingredient in the
gypsum core. This ingredient is a
shrinkage-compensating additive, a
form of vermiculite. When exposed to
high heat, the gypsum core shrinks
but the shrinkage-compensating element
expands at about the same rate
as shrinkage occurs in the waterdepleted
gypsum.
The gypsum core then is more
stable in a fire and remains in place
even after the combined water in the
gypsum has been driven off.
A is a fire caused by burning solids. B is a fire caused by burning liquids. C is a fire caused by electricity. BC fire extinguishers should not be used against type A fires, but ABC fire extinguishers can be used against all three fires.
Start and stop codons
First priority is to remove the source of the electricity. Without that, the fire will continue to form. After disconnecting the electrical source, put out the fire as normal, with a co2 extinguisher and foam. Sand works too.Improvement:Sand is the best option after a CO2 extinguisher. Improvement:I agree but you could also try smothering it with a fire blanket (if you don't have a CO2 extinguisher lying around!) to take away the oxygen BUT NEVER put water on an electrical fire it just makes it worse.IMPROVEMENT;here are some good tips,NEVER USE WATERif it is small you could use some baking sodaan ABC or class C fire extinguisher are best
take out the drywall (2 x 1/2") and you have 59"
firse, find any moister, if u have drywall mold is on the backside usually starting from the bottom.if u have a cinderblock foundation and drywall.90% will have mold find any soft spots and make a hole,look at backside, well...now u know
Type C drywall is designed for areas where fire resistance is required, offering a higher level of protection compared to Type X drywall. Type X drywall is also fire-resistant but has a lower fire rating than Type C. Additionally, Type C drywall is typically thicker and denser than Type X drywall, providing better soundproofing and impact resistance.
It's drywall that has a fire resistant additive, and is also thicker.
Fire code drywall typically weighs around 2.3 to 2.8 pounds per square foot. This weight can vary depending on the specific type and thickness of the fire-rated drywall being used.
Approximately 110 pounds.
The recommended code for installing drywall in a garage is to use fire-resistant Type X drywall on the walls and ceiling, with all seams taped and mudded for a smooth finish. Additionally, it is important to ensure proper insulation and ventilation to meet safety standards.
It is drywall that will be fire-resistant for 3 hours.
To ensure maximum fire protection when applying fire-rated drywall mud, it is important to follow these best practices: Use the correct type of fire-rated drywall mud that meets building code requirements. Apply multiple layers of fire-rated drywall mud as recommended by the manufacturer. Make sure to properly mix and apply the drywall mud according to the manufacturer's instructions. Pay attention to the thickness and coverage of the drywall mud to ensure adequate fire protection. Allow sufficient drying time between layers to ensure proper adhesion and effectiveness. Inspect the finished application for any gaps, cracks, or imperfections that could compromise fire protection. By following these best practices, you can help maximize the fire protection provided by fire-rated drywall mud in a building.
Specific building regulations for installing drywall in a garage according to the local building code may include requirements for fire resistance, thickness of the drywall, and proper installation techniques to ensure safety and compliance with building standards. It is important to consult the local building code or a professional contractor for detailed information on specific regulations in your area.
You use 5/8 fire proof drywall on both sides.
The code-specified maximum thickness for ceiling drywall is typically 5/8 inch.
Fire-resistant drywall provides increased protection against fires by slowing down the spread of flames and reducing the risk of structural damage. This can help save lives, minimize property damage, and meet building code requirements for safety.
It is drywall that will be fire-resistant for 3 hours.