To transform a shower from dull to dramatic, tile a shower wall. Here's how to do it: Step 1: Measure the walls carefully; shower walls are seldom perfectly square and plumb. Do a dry layout of the tile (including spacers) on the floor using your measurements. Step 2: Working in a small section, spread thinset with a notched trowel and press the tile into place. Step 3: When the tile has set - typically about 24 hours - you can apply the grout. Mix grout in small batches that you will be able to use within 20 to 30 minutes. Step 4: Wait 24 hours and apply sealer to all the joints - and the tile if recommended. Natural stone and some other tiles will need a sealer to keep them from absorbing water. Gazed porcelain and ceramic tiles are already sealed.
Corian type of tile is best to surround your bathtub because its perfect for wet walls, if you know what I mean. You can find it mostly anywhere. I usually go to Home Depot but im not sure if they sell it where you live.
Probably yes, but it depends on the exact labeling on that mortar, and what kind of tile and wall surface you have. Check to see what kinds of tile (ceramic, porcelain, travertine, etc.) it sticks to, and what size of tile. Also see what kinds of substrates it's approved for. Substrate is the surface to which you want to attach the tile. If the bag says it sticks to cementious backerboard, and you have tile backerboard on the walls, then it's good to go.
There are some tools for cutting tiles. You can use a circular saw or a manual tile cutter. But for tile cutting best is tile saw. Ceramic tiles are chipping easily thats why wet tile saws are best for cutting ceramic tiles.
You do not want to use a mixing thinset for backsplash. you would want to use something a little stronger for walls, being a carpenter for 7 years i would use mastic tile adhesive. There are alot of advantages in using this product and the main reason is most of it is pre mixed. The mastic tile adhesive is an organically based mortar that is commonly used in the laying of ceramic tiles. This adhesive is made from the resin of the mastic tree and is available as a thin liquid, a paste, or a glue. Some common construction adhesives are a form of mastic resin. Using mastic as a tile adhesive does carry some advantages over mortar.1. Tremendous Holding StrengthMastic is used mostly with ceramic tile, but is also used with heavier materials such as stone and marble. This strength is the reason that many people will use a mastic tile adhesive in shower enclosures where there is a stone tile. If the seal remains the tile, then mastic adhesive will last for many years without any problems.2. Quick Setting Tile AdhesiveThe mastic tile adhesive is very quick setting. While this does have some drawbacks to it, it is also an advantage. Heavier tiles will set quicker so you can get more of the project competed.3. Easy to UseWhen spreading out over a backerboard to apply the tiles to, mastic tile adhesive is much easier to work with than mortar. Not being as thick, the mastic spreads out evenly and gives the tile a very good area to bond with.Read more: http://www.doityourself.com/stry/3-advantages-of-using-mastic-tile-adhesive/#b#ixzz23kIZTizw
Yes, but you should you use an adhesive that is ductile
There are other wall coverings besides tile. Also, you could use larger floor tile to make the work easier. Maybe an exterior paint would work, but should you want to sell, the buyers would see this as a bad shortcut.
To prepare shower walls for tile installation, start by ensuring the walls are clean and dry. Next, apply a waterproofing membrane to protect against moisture. Then, use a level to mark guidelines for the tile layout. Finally, apply thin-set mortar to the walls and press the tiles into place, making sure they are evenly spaced and level. Allow the mortar to dry before grouting the tiles.
You can use floor tile in the shower, perhaps certain types that specify that you can't are an exception. There is literally no reason why you can't. I have been using matching floor tile on shower walls for years. Just make sure that if you have to use thinset to do so, instead of glue. Make sure you have denshield or Cementboard as the board being used to set on, and make sure that you know what you are doing, because if not it will most likely look terrible, and fall apart.
Your question is a little vague. The walls will be built the same as the other walls in the structure, but will usually be finished with a concrete wallboard such as Durock. Water resistant drywall also known as "green rock" would be the minimum if you did not use the Durock. Then, the shower stall walls or tile would be installed on top of that. Does this answer your question?
It is not the soap you use, but rather the cleaner. Soft-scrub does a nice job about cleaning walls, in addition to Clorox spray bleach for removal of soap scum.AnswerI spray the shower walls down with Clean Shower. Once a year, I scrub it down. If you don't want to use chemicals, squeegee or wipe down the shower each time you finish.
yes that's what i did.
Yes you can use marble tile in shower and it can enhance the look of your bathroom. Please see the related links below.
The best materials to use for a tile shower floor are porcelain or ceramic tiles. These materials are durable, water-resistant, and easy to clean, making them ideal for a shower environment.
You can clean a shower tile in many ways. You can use a cleaner that is formulated for cleaning tile. You can also use vinegar, dish soap, and water. Simply apply the cleaner of your choice and use a soft cloth, sponge, or brush.
Yes, you can tile over drywall in a shower, but it is recommended to use a waterproof backer board instead for better moisture resistance and durability.
To create a stunning mosaic tile shower in your bathroom, follow these steps: Plan the design and layout of the mosaic tiles. Choose high-quality mosaic tiles that complement your bathroom decor. Prepare the shower walls by cleaning and priming them. Apply thinset mortar to the walls and start placing the mosaic tiles. Use tile spacers to ensure even spacing between tiles. Allow the mortar to dry completely before grouting the tiles. Apply grout to fill in the gaps between the tiles and wipe off excess grout. Seal the grout to protect it from moisture and stains. Enjoy your stunning mosaic tile shower!