answersLogoWhite

0

the root opening is the distance between joint members at the root of the weld before welding. the root opening must be accurate so that excess welding is not necessary.

User Avatar

Wiki User

12y ago

What else can I help you with?

Continue Learning about Geometry

What is the rough opening requirement for an interior door that is 3 foot with a frame size of 3 foot 1-58?

The rough opening of an interior door is two inches wider than the width of the door and two inches higher than its height. Thus your rough opening width is 38". A typical interior door has a height of 80" which would require a rough opening height of 82" but check your door to ensure that is theheight.


Why are king size box springs 2 pieces?

If they were one-piece they wouldn't fit through a standard door opening.


Number of square units to cover a flat surface in math?

Are determined by (a) the shape of the flat surface, (b) the area of the flat surface, and (c) the size of the square units.


What is sugar mesh size?

Sugar mesh size refers to the granulation or particle size of sugar, which is determined by the size of the sieve used to classify it. A smaller mesh size indicates finer sugar particles, while a larger mesh size corresponds to coarser sugar. For example, powdered sugar typically has a mesh size of 100 or higher, while granulated sugar may fall between 20 to 30 mesh. This classification affects the sugar's solubility, texture, and suitability for various culinary applications.


How big is a bathroom door opening?

The smallest door I have seen on house building plans is 2'0". The smallest door I have framed for and installed is a 2'4" door. That is the smallest size door I recommend anyone put in. For the handicapped or wheelchair bound the minimum size required is 3'0". sawkerfs

Related Questions

What size welding rod needed two do a root weld?

The size of the welding rod needed to do the root pass should be the same as the root gap, although in practice, the most common root gap is 1/8" so that the size of the rod to do it is also 1/8".


How is a vise size determined?

The width of the jaws (not the opening)


Welding current for a 3.2mm rod?

The current requirement while welding with 3.2 mm size electrode varies with wether it is root pass or second or capping pass. As for root pass value of current will be () and for 2nd or capping pass its value will be ().


What is the maximum opening size allowed in a load-bearing wall?

The maximum opening size allowed in a load-bearing wall is typically determined by the structural engineer and building codes to ensure the wall's strength and stability are not compromised.


What does 7016 stand for on a welding rod?

for steel structure building can i use: -size 2.5mm of 7016 welding rod as a filler for welding IPE240 to plates -size 2.5mm of 7016 welding rod as 2nd pass


What is the effect on welding with wrong size?

no effect


What are two effects that joint design has on the completed weld?

I am not sure but I would assume two things about joint design and its effect on the weld and visa versa: penetration and overall strength of the weld would depend greatly on what grove you are welding in or on and the amount of distortion would vary greatly depending on how large of root opening and weld size etc.


How small of an opening should a lintel be put in?

It's not a question of opening size but a question of loading over the opening. No load, no lintel. If a 12 inch opening is capped with a 16" block, the block is the lintel. If an opening is between wall studs there is little need for anything that would be called a lintel. Anouther name for a lintel is a header. There is usually some kind of header over an opening. A lintel's size and integrity is determined by the load it will support.


What are the gas pressures and flow rates in relation to the type of material being welded?

Gas pressures and flow rates are typically determined based on the type of material being welded, the welding process, and the size of the weld joint. For example, when welding aluminum, higher gas flow rates and pressures may be required compared to welding steel due to its higher thermal conductivity. It is important to consult welding procedure specifications and guidelines provided by the welding equipment manufacturer to determine the appropriate gas settings for different materials.


Whether HAZ is higher in gas welding or arc welding?

Larger in Gas Welding. In all arc processes the HAZ is concentrated in a couple inches around your bead. In gas welding it can be double or triple that size.


The physical size of an atom is largely determined by?

The physical size of an atom is largely determined by the size of the electron cloud.


How is eggs size determined?

It is determined by the weight not the height