0
How do you keep the paint from burning off the fender and door when welding a broken fuel door hinge?
I would try to use small tack welds all the way around the latch if I had to weld it...but my advice is to hold the fuel door in place, or have someone hold it for you, and then drill two small holes through the hinge and into the body of the car, and screw two small metal screws into place. If the heads of the screws are getting in the way, you can grind them down with a small rotary tool or likewise to where about 1mm is left of the screw, and that should solve your problem.
What else can I help you with?
How do you remove rusted front door in a 1993 dodge caravan the bolts are under the fender. does the fender have to be removed.?
the fender must be well loosened or removed to get to the hinge bolts
If your driver side door is loose and you have to slam it to close how do you tighten it up to make it like the passenger side?
Have someone lift and shake the door while you watch the hinges to see if they are loose. If the hinge pins are worn, the door will sag and make it difficult to close. You also may need to replace the nylon bushing on the door strik pin if there has been too much weight when the door closes. The strike pins can be replaced but if you haven't already done one, you might want to have someone help you or do it for you. It happened to me. If you open the door, lift up and down on the bottom of the door to see if it loose where the door hinge is bolted to the fender. If it loose where it is bolted to the fender, you will need to tighten the bolts. If the nuts are stripped in the fender, take it to the body shop. What was stripped in my door was the nuts inside the fender that the bolts went into. You could just have a stripped bolt. I had the choice of taking off the whole fender to fix it or weld the door hinge tho the fender. I chose to have the body shop weld the hinge (much cheaper). They did a perfect job welding the hinge so the door fit and matched perfect. I bought the car used and the fit was better that when I bought it.
How can I fix a toilet seat hinge that is loose or broken?
To fix a loose or broken toilet seat hinge, you can try tightening the screws with a screwdriver. If the hinge is broken, you may need to replace it with a new one. Make sure to follow the manufacturer's instructions for proper installation.
How do you use hinge in a sentence?
Perry Mason's entire case will hinge upon this very point. The door will not swing without a hinge.
How do you repair a broken door hinge on a 1991 Cherokee Briarwood where it should be welded onto the frame?
To repair a broken door hinge on a 1991 Cherokee Briarwood, a new piece of metal should be welded in to hold the hinge. Then, a new hinge should also be welded in that is aligned with the door pin.
Where is the single wire in line spout connector on 93 f150?
Drivers side fender well by the hood hinge
How much will it cost for you to send in your ds to fix a broken hinge?
£35
How do you fix a broken hinge on x-cargo sport-20?
Order it from e-trailer
1986 GMC Vandura rear door hinge is broken - Replace?
To replace the broken rear door hinge on a 1986 GMC Vandura, start by removing any interior panels or covers to access the hinge area. Support the door while removing the old hinge bolts using the appropriate tools. Install the new hinge by aligning it with the door and body, then securely fasten the bolts. Finally, reattach any interior panels and test the door's functionality.
How do you get the pivot or rivet off of the passenger side hood hinge of a 92 Olds 98 so you can replace the broken hinge?
If it is a rivet, then you must drill the old rivet out.
What should I do if I have a broken toilet seat hinge?
If you have a broken toilet seat hinge, you should consider replacing the hinge or the entire toilet seat. You can find replacement parts at hardware stores or online. Make sure to follow the manufacturer's instructions for installation. If you're not comfortable doing it yourself, consider hiring a professional plumber to help.
How do you fix broken hinge on a glove box in A 2007 Buick rendezvous?
To fix a broken hinge on the glove box of a 2007 Buick Rendezvous, first, remove the glove box by unscrewing any fasteners and disconnecting the dampener arm. Inspect the broken hinge and either replace it with a new one or repair it using strong adhesive or epoxy if possible. Reattach the glove box by securing it back in place and ensuring that the hinge operates smoothly. Finally, test the glove box to ensure it opens and closes properly.
