mujhe nhi pta..inch tape waalon ne chutiya kaat rakha hai.......maul lo roj lo....jai gyan devta....jai badhra kali...
On a standard tape measure, 5.1 inches would be represented by the fifth line after the 1-inch mark. Each inch is divided into 16 equal parts, so the 5.1 inch mark would fall between the 5-inch mark and the 6-inch mark. It is important to note that some tape measures may have additional markings for greater precision, such as 1/8 or 1/16 inch increments.
It is a journalism, proofreader and typesetter mark meaning the end or finished.
There were mark numbers from 1 to 24 with many variations, also about 8 marks of Seafire. Every mark had many variations so there was a large number of slightly different aircraft.
Well 5/8 is 0.625, so it is close to 1 5/8. Find the little marks which are 1/8 inch, and it will be one greater than the 1 1/2 inch mark.
On a standard tape measure, the number 4.625 typically represents 4 feet and 7 inches. The whole numbers on a tape measure usually indicate feet, while the smaller increments between the whole numbers represent inches. In this case, the number after the decimal point (0.625) corresponds to 7/8 of an inch, which is typically the next smallest increment after 3/4 of an inch on a tape measure.
The stud distance in houses.
1.54 inches on a measuring tape is slightly more than one and a half inches. It falls between the 1.5-inch mark and the 1.6-inch mark. To visualize it, you can find the 1.5-inch mark and then count a little past it, which is slightly less than 1/16 of an inch from the 1.5-inch mark.
Because that is a common stud placing in frame buildings.
Every half inch.
On a ruler, 0.33 inches is slightly more than one-third of an inch. It is positioned between the 1/4 inch mark (0.25) and the 1/2 inch mark (0.5). You can estimate it as just under the 3/8 inch mark, which is approximately 0.375 inches. If measuring in centimeters, 0.33 inches is about 0.84 cm.
On a standard ruler, 7.9 inches would fall between the 7-inch mark and the 8-inch mark. Each inch on a ruler is divided into 16 equal parts, so 0.9 inches would be just slightly before the 1-inch mark after the 7-inch mark. To locate 7.9 inches precisely, you would count 7 full inches and then estimate just under a tenth of an inch beyond the 7-inch mark.
It depends on the measuring instrument (tape or ruler) being used. Some are marked in 1/8 inch, some in 1/10 inch, some in 1/16 inch and, rarely for such long rulers, 1/32 inch.
between 5 3/4 and 6 inch marks almost to the 6 inch mark, but not quite
.30 inches on a tape measure is a little less than one-third of an inch. It can be found by locating the 1/4 inch mark (which is 0.25 inches) and then measuring an additional 1/20 of an inch past that mark. On most tape measures, this would be represented as a small division between the 1/4 inch and 3/8 inch marks.
To measure to the nearest 16th of an inch, first use a ruler or tape measure that has markings for 16ths. Align the zero mark with one end of the object you are measuring, then locate the nearest whole inch or half-inch mark. Count the 16th-inch increments from that mark to the other end of the object, rounding to the nearest increment if necessary. For example, if the measurement falls between 3 and 4 inches and is closer to the 3 7/16 mark than to 3 1/2, you would record it as 3 7/16 inches.
3.35 inches on a tape measure is a little over 3 and one-third inches. It can be found by locating the 3-inch mark and then measuring an additional 0.35 inches past it. This additional measurement corresponds to just over one-third of an inch, as there are 0.33 inches in one-third. On a standard tape measure, you would see the 3-inch mark and a bit more toward the next 4-inch mark.
Five eighths of an inch on a ruler would be located between the half-inch mark and the three-quarter inch mark.