answersLogoWhite

0

The ring fetter is made up of 3 pieces. The outer cylinder, inner cylinder and the locking bolts. As you draw in on the locking bolts (usually caps screws) the inner and outer cylinders are squashed together locking the shaft to the bearing. To remove there are jacking bolt holes. The ring fetter is a one shot deal. the cylinders are distorted and win not seat properly again.

Bob Page

Maintenance Mechanic

Covidien

User Avatar

Wiki User

14y ago

What else can I help you with?

Related Questions

Oil blowing out of distributor on 1994 Chevy caviler convertable?

There is a rubber O-ring seal on the distributor shaft. You will need to pull that shaft and replace the O-ring. Fairly easy job. The O-ring will cost you about $1 if you can do the work yourself.


What is the shaft work formula used to calculate the work done by a rotating shaft?

The shaft work formula used to calculate the work done by a rotating shaft is: Work Torque x Angular Displacement.


What is the shaft work equation used to calculate the work done by a rotating shaft?

The shaft work equation is used to calculate the work done by a rotating shaft. It is given by the formula: Work Torque x Angular Displacement. This equation helps determine the amount of energy transferred by a rotating shaft.


Can copper dwv attach to a cast iron drain system without a dielectric union?

yes. A no-hub coupling or FERNCO (brand name) coupling work well.


How does shaft encoder work?

A shaft encoder is also known as a rotary encoder. The shaft encoder converts an angular position of a shaft to a digital code.


What is it called when wind and ocean currents work together?

Could it be Ocean-Atmosphere Coupling.


How do you take apart the rearend on 1998 crown vic?

jack up high enough to work underneath,remember to use stands, take brake pads and califper out,then take a rearend plate ,then take a horse-shoes ring from an axle shaft,then take an axle shaft out.Have fun


What is shaft work and flow work?

Shaft work refers to the work done on a system by a rotating shaft, such as a turbine or motor. Flow work, also known as pressure-volume work, is the work done by a fluid moving through a system due to changes in pressure or volume. Both are important concepts in thermodynamics for analyzing energy transfers.


In an electromagnetic what turns the drive shaft that does the Work?

An iron or steel with wire wound on it turns the drive shaft.


How does rolling ring drive works?

The inner race of a "rolling ring" bearing is specially contoured to form a central "ridge" which runs around the entire inner race surface of the bearing.When mounted on a shaft of rolling ring drive, a rolling ring bearing contacts the shaft only on the apex of this central ridge. The bearing may be "pivoted" left or right on the shaft, and still maintain point contact with the shaft.In a rolling ring linear drive, an assembly of three or four rolling ring bearings is fixed and compressed within a housing. A smooth, threadless shaft is inserted through the housing, and through the rolling ring bearing assembly.When the rolling ring bearing assembly is angled on the smooth shaft, and the shaft is rotated, compression against the central ridge surface is generated causing the bearings to "roll" along the length of the shaft. The rotary motion input provided by the motor-driven shaft is thereby converted to linear motion output. The housing, which bears the payload, moves along with the rolling ring bearing assembly. The angle of the rolling ring bearing assembly, relative to the shaft, determines travel direction and pitch (distance traveled per shaft revolution).No backlash -- Advantage over precision ball screwsBacklash is inherent to ball screw design. It results from the amount of clearance between the ball bearing and the threads. Backlash is caused by clearance or "play" between contacting surfaces in ball screws, gears, belt drives and other linear motion devices. To overcome backlash, ball screw users typically preload the nut to keep the balls under steady pressure. Other methods for fighting backlash include active cam mechanisms, shims and other devices which load the geartrain. These methods can be expensive. And their performance level deteriorates over time due to wear and tear. Okcoil rolling ring drives require no preload to eliminate backlash. Rolling ring engineering assures continuous point-contact between the rolling ring bearing surface and the shaft. There is no "play" and virtually zero backlash - even during reversal. Additionally, rolling ring drives ( trvaverse units) have built-in overload protection. If the system is overloaded, the nut will slip, not jam. Ball screws can't match these features. And ball screws require a significant, up front investment to reduce of backlash before the system can be used for precision linear motion control work.


What is the purpose of a coupling?

A coupling capacitor does the same work as its name suggests, that is coupling one stage of the electronic circuit with another. It does that without passing the DC bias voltages between stages so that these stages are not affected by each other.To block or avoid the flow of D.C and to allow only A.C


What are the standard units used to measure shaft work in mechanical systems?

The standard unit used to measure shaft work in mechanical systems is the Joule (J).