0
To relight the pilot light on your Honeywell water heater, follow these steps:
- Locate the gas control knob and set it to the "off" position.
- Wait for at least 5 minutes to allow any lingering gas to dissipate.
- Turn the gas control knob to the "pilot" position.
- Press and hold down the pilot button while using a long lighter to ignite the pilot light.
- Continue holding the pilot button for about 60 seconds after the pilot light is lit.
- Release the pilot button and turn the gas control knob to the desired temperature setting.
- If the pilot light does not stay lit or you smell gas, turn off the gas supply and contact a professional for assistance.
What else can I help you with?
How can I troubleshoot and relight the Honeywell furnace pilot light?
To troubleshoot and relight the Honeywell furnace pilot light, first check for any gas leaks or blockages in the pilot tube. If there are no issues, follow the manufacturer's instructions to relight the pilot light using the reset button or control knob. If the pilot light continues to go out, it may indicate a more serious problem that requires professional assistance.
How can I determine if the water heater pilot light is out?
To determine if the water heater pilot light is out, locate the pilot light access panel on the water heater. Look inside to see if the pilot light is lit. If it is not lit, you may need to relight it following the manufacturer's instructions.
How can I relight the water heater pilot?
To relight the water heater pilot, locate the pilot light button or knob on the water heater. Turn it to the "pilot" setting and hold it down. While holding the button down, use a long lighter to ignite the pilot light. Keep holding the button for about a minute after the pilot light is lit to ensure it stays on. If the pilot light continues to go out, there may be an issue with the thermocouple that needs to be addressed by a professional.
How do you relight a natural gas pilot light?
How do you relight a natural gas pilot light?
How can I check the water heater pilot light?
To check the water heater pilot light, locate the access panel on the water heater and look for a small flame. If the flame is out, follow the manufacturer's instructions to relight it safely.
Why did my water heater pilot light go out?
The pilot light on your water heater may have gone out due to a variety of reasons, such as a faulty thermocouple, a clogged pilot orifice, a gas supply issue, or a draft in the area where the water heater is located. It is important to troubleshoot and address the specific cause to safely relight the pilot light.
What should I do if the pilot light is out on my hot water heater?
If the pilot light on your hot water heater is out, you should follow the manufacturer's instructions to relight it. This typically involves turning off the gas supply, waiting for any gas to dissipate, and then using a long lighter to relight the pilot. If you are unsure or uncomfortable doing this, it is best to contact a professional plumber or the manufacturer for assistance.
How do I relight a heater's pilot light?
Usually you can relight it with a lighter, and it will be good. If not you should shut it off so that you don't have a fuel leak. It shouldn't take much to fix any way.
How to light a water heater with an electronic pilot by Honeywell?
To light a water heater with an electronic pilot by Honeywell, follow these steps: Locate the control panel on the water heater. Turn the control knob to the "Pilot" position. Press and hold the pilot button while pressing the ignition button. Continue holding the pilot button for about 30 seconds to allow the pilot flame to ignite. Release the pilot button and turn the control knob to the desired temperature setting. Always refer to the manufacturer's instructions for specific details on lighting your water heater.
What are the steps to relight the pilot on a hot water heater?
To relight the pilot on a hot water heater, follow these steps: Locate the pilot light assembly on the water heater. Turn the gas control knob to the "off" position and wait for at least 5 minutes. Turn the gas control knob to the "pilot" position. Press and hold down the pilot button while using a long lighter to ignite the pilot light. Continue holding down the pilot button for about 30 seconds after the pilot light is lit. Release the pilot button and turn the gas control knob to the desired temperature setting. Remember to refer to the manufacturer's instructions for specific guidance on relighting the pilot on your particular water heater.
Why won't the pilot light on my water heater that got wet?
When a pilot light on a water heater gets wet, it may not light because the water can disrupt the flow of gas or cause electrical issues, preventing the ignition process. It is important to ensure the area is dry and free of moisture before attempting to relight the pilot light.
How do I check the pilot light on my water heater?
To check the pilot light on your water heater, locate the access panel near the bottom of the unit. Open the panel and look for a small flame burning inside. If the flame is out, follow the manufacturer's instructions to relight it safely.
