The outside diameter of a 1/2 inch PVC pipe is approximately 0.840 inches.
The outside diameter of 12-inch transite pipe is typically around 12.75 inches. Transite pipe, made from a mixture of cement and asbestos, often has a slightly larger diameter than the nominal size due to its construction. However, it's important to check specific manufacturer specifications, as dimensions may vary slightly.
The circumference of 12-inch pipe is: 37.7 inches. (C = d x Pi)Since 12 inch pipe is a nominal size and its outside diameter is 12.75 inches, the circumference of 12 inch pipe actually is : 40.035 inches
The formula for working out the circumference of a circle (like a pipe) is diameter times pi. (You should find pi on your calculator, if not, it is 3.14159265) Since you know the circumference, you divide the circumference (5inch) by pi (3.14159265), and you get the diameter, i.e. the size pipe. While the above formulas are correct, using this equation example will not tell you what size pipe you have. There are a number of factors involved in determining the correct answer. There are many different materials that pipe is made out of and some of these affect the dimensions of the pipe. As an example, the actual outside diameter of 1" copper pipe and 1" steel pipe are not the same. If you are talking about steel pipe, it is important to understand that all pipe 12 inch and under is referred to as "nominal" pipe size. In this case, the outside diameter of 12 inch pipe is actually 12.75 inches. For the original question asked above, the 5 inch circumference would equal 1-9/16" outside diameter which would be the equivalent of 1-1/4" pipe (nominal).
If a pipe is 12 inches aroud, then that is its circumference. The width is the diameter. To get the diameter, you'll have to divide 12 by pi, or 3.14, and the answer you get is 12/3.14=3.82.
Assuming that the INNER DIAMETER of the PVC pipe is 4" (...likely not the case, so you'll need to recalculate for your pipe's dimensions): the volume of the pipe would be calculated as follows: 4" diameter = 2" radius volume_cylinder = Pi*r^2*L; where r = 2" and L = 12" the cylinder therefore has a capacity of 150.8 cubic inches. a gallon of water has the volume of 231 cubic inches. your pipe can hold 0.653 gallons of water. you'll need about 18.38 inch lengths of 4" PVC to hold each gallon of water. again, these calculations rely on the INNER DIAMETER of the pipe being measured at 4" - if this is an outer diameter measurement, the above calculation for the capacity is OVERstated; the 18.38" calculation is UNDERstated.
To calculate the outside diameter of a roll of carpet, you can use the following formula: Outside Diameter (in inches) = √[(Weight in pounds / (Width in feet x Length in feet)) * 32] In your case: Weight = 1000 pounds Width = 12 feet Length = 180 feet Outside Diameter (in inches) = √[(1000 / (12 x 180)) * 32] Outside Diameter ≈ √[(1000 / 2160) * 32] Outside Diameter ≈ √(0.1481 * 32) Outside Diameter ≈ √4.7392 Outside Diameter ≈ 2.18 inches So, the outside diameter of a 1000-pound roll of carpet that is 12 feet by 180 feet is approximately 2.18 inches.
about 10$ per foot ANS 2 You're going to the wrong store if you pay that much. I regularly buy it in Canada for 2.85 per foot.
about 25 bucks per foot .
A PVC pipe glue will take at least 4 hours to dry. 12 hours before putting water pressure in it.
You can dig to the pipe, clean it and roughen it, then use purple primer and Weld On 711 to repair it. . I would wait 12 hours for this to cure then do another coat of 711. - I have done this on PVC pipe that was carrying mains water at 85 psi.
It is: 12/pi = 3.8197 inches rounded to 4 decimal places
Go to Appendix C of the NEC book