CRIB ASSEMBLY INSTRUCTIONS
(OLD SYSTEM)
WARNING
FAILURE TO FOLLOW THESE WARNINGS AND ASSEMBLY INSTRUCTIONS CAN
RESULT IN SERIOUS INJURY TO THE CHILD.
*READ ALL INSTRUCTIONS BEFORE ASSEMBLING CRIB.
KEEP INSTRUCTIONS FOR FUTURE USE.
*BEFORE EACH USAGE OR ASSEMBLY, INSPECT CRIB FOR DAMAGED
HARDWARE, LOOSE JOINTS, MISSING PARTS OR SHARP EDGES.
DO NOT USE CRIB IF ANY PARTS ARE MISSING OR BROKEN. ASK YOUR
DEALER OR WRITE TO RAGAZZI FOR REPLACEMENT PARTS AND
INSTRUCTIONAL LITERATURE IF NEEDED.
DO NOT SUBSTITUTE PARTS.
DO NOT USE THIS CRIB FOR A CHILD WHO IS ABLE TO CLIMB OUT UNAIDED
OR WHO IS TALLER THAN 35 INCHES (90 CM).
*DO NOT PLACE CORDS, STRAPS OR SIMILAR ITEMS THAT COULD BECOME
WOUND AROUND A CHILD'S NECK IN OR NEAR THIS CRIB.
*IF REFINISHING, USE NON-TOXIC FINISH SPECIFIED FOR CHILDREN'S
PRODUCTS.
*DO NOT LEAVE CHILD IN CRIB WITH SIDE LOWERED. BE SURE SIDE IS IN
RAISED AND LOCKED POSITION WHENEVER CHILD IS IN CRIB.
*WHEN CHILD IS ABLE TO STAND IN CRIB, SET MATTRESS TO LOWEST
POSITION AND REMOVE BUMPER PADS, LARGE TOYS AND OTHER OBJECTS
THAT COULD SERVE AS STEPS FOR CLIMBING OUT.
*NEVER USE PLASTIC SHIPPING BAGS OR OTHER PLASTIC FILM AS
MATTRESS COVERS BECAUSE THEY CAN CAUSE SUFFOCATION.
*DO NOT USE WATER MATTRESS WITH THIS CRIB.
*REPLACE TEETHING RAIL IF DAMAGED OR LOOSE.
*CAUTION: ANY MATTRESS USED IN THIS CRIB MUST BE AT LEAST 27-1/4
INCHES BY 51-3/8 INCHES WITH A THICKNESS NOT EXCEEDING 6 INCHES.
IMPORTANT
PARENTS SHOULD ENSURE A SAFE ENVIRONMENT FOR THE CHILD BY
CHECKING REGULARLY, BEFORE PLACING THE CHILD IN THE CRIB, THAT
EVERY COMPONENT IS PROPERLY AND SECURELY IN PLACE.
CRIB ASSEMBLY (SEE DIAGRAM )
CONTENTS:
2 end panels (headboard + footboard) (A), with 2 top long plastic glides (a)
and 2 bottom metal glides (b);
1 stationary side rail (B);
1 drop side rail (C), with 2 top plastic guides (c)
and 2 bottom locking mechanisms (d);
1 mattress support (D);
6 brass bolts;
1 Allan key;
4 hexagon bolts 1/2";
8 metal washers (if required);
1 stabilizer bar (available only for certain models) (E).
2 metal pins
STEP 1 Attach the stationary side rail (B) to end panels (A) with four brass bolts.
Use Allan key provided.
STEP 2 Attach the mattress support (D) to end panels (A) at desired position with the four
1/2" hexagon bolts.
To change the position of mattress support (D), unscrew the four 1/2"
hexagon bolts, line up mattress support (D) with holes at desired position and
reattach it with the 1/2" hexagon bolts.
STEP 2.1 (Applicable only for certain models). Attach the stabilizer bar (E) to end panels (A)
by placing the metal pins in upper holes of bar and inserting in upper holes of ends.
Secure bar using two brass bolts in lower holes of bar and end panels.
NOTE:
THE MATTRESS SUPPORT SHOULD BE AT THE HIGHER LEVEL WHEN CHILD IS
BORN. IT SHOULD BE AT THE LOWER LEVEL BEFORE CHILD CAN STAND UP.
STEP 3 INSTALLATION OF DROP SIDE (C) (see diagram)
Lay crib on its side, on the ground;
Remove rubber stoppers at bottom of metal glides (b) found on end panel (A);
Slide drop side rail (C) in tracks all the way up;
Re-insert the rubber stoppers on bottom metal glides (b);
Be sure to tighten properly.
STEP 4 CASTERS:
Slip the four casters into inserts located inside holes of end panel (A). Press firmly
to lock in place.
DROP SIDE OPERATING INSTRUCTIONS:
After the crib is assembled: raise the drop side to the upper or closed position.
TO LOWER: Hold the center of the upper rail of the drop side with one hand. Raise the drop side
(C) until it stops. With the drop side (C) held in this position, press against the bottom rail of the
drop side (C) with your leg at the point marked "PUSH" on the plastic plate. Then lower the drop
side (C) until it connects with the rubber stopper on the bottom metal glides (b).
TO RAISE: Hold the center of the upper rail of the drop side with one hand. Lift the rail until drop
side bottom locking mechanisms (d) snap in place.
Crib drop side rail (C) is now closed and locked in place.
ADDENDUM:
Metal washers are to be used on crib only if there is a tension in the crib drop side rail (C).
TO RELIEVE TENSION:
1) Remove drop side rail (C);
2a) WHEN TENSION IS PUSHING OUTWARD:
Place metal washers between bottom metal glides (b) and headboard and footboard (A);
2b) WHEN TENSION IS PULLING INWARD:
Place metal washers between stabilizer bar (E) and headboard and footboard (A):
3) Re-install drop side rail (C)
DAY BED INSTRUCTIONS
1 - Remove drop side rail ( C ) as follow:
Lay crib down on its stationary side rail.
Remove rubber stoppers at bottom of metal glides (b) found on end panels (A)
Slide drop rail (C) down the tracks.
2 - Re-insert the rubber stoppers on the bottom metal glides (b)
3 - Remove the plastic and metal glides (a & b) from end panels (A)
4 - Ensure that the mattress support (D) is in the lowest position.
5 - For safety reasons, stabilizer bar (E) must be installed in order for crib to be used as a
To safely lower the mattress in a crib, first remove any bedding or toys from the crib. Then, locate the mattress support platform and find the adjustable settings. Lower the mattress to the desired height by following the manufacturer's instructions. Make sure the mattress is securely in place before placing your baby back in the crib.
To safely lower a crib mattress to the floor, first ensure that the crib is designed to allow for mattress height adjustments. Follow the manufacturer's instructions carefully to lower the mattress to the lowest setting. Make sure all parts are securely in place before placing your baby in the crib.
To safely lower a crib mattress for your baby's comfort and safety, follow these steps: Remove any bedding or toys from the crib. Locate the mattress support platform underneath the mattress. Look for the adjustable settings on the platform. Lower the platform to the desired height, ensuring it is securely in place. Double-check that there are no gaps between the mattress and the crib sides. Test the firmness of the mattress to ensure it provides proper support for your baby.
To safely lower a crib for your growing baby, follow these steps: Remove the mattress from the crib. Locate the adjustable mattress support platform. Unscrew or release the locking mechanism on the platform. Lower the platform to the desired height. Securely reattach the locking mechanism. Place the mattress back in the crib. Ensure all parts are securely in place before placing your baby in the crib.
To safely lower a crib bed for your baby's comfort and safety, follow these steps: Remove the mattress from the crib. Locate the adjustable mattress support platform. Unscrew or release the mechanism that holds the platform in place. Lower the platform to the desired height. Secure the platform in the new position. Place the mattress back in the crib. Ensure all parts are securely in place before placing your baby in the crib.
To safely lower a crib mattress to the floor for your baby's sleep environment, follow these steps: Remove any bedding or toys from the crib. Lower the mattress to the lowest setting, ensuring it is securely in place. Double-check that all sides of the crib are locked in the lowered position. Test the stability of the mattress by gently pressing down on all corners. Once you are confident the mattress is secure, add a fitted sheet and any necessary sleep items for your baby. By following these steps, you can create a safe and comfortable sleep environment for your baby.
To adjust the height of a crib mattress for your baby's safety, follow the manufacturer's instructions. Typically, you can lower the mattress as your baby grows and becomes more mobile to prevent climbing or falling out of the crib. Make sure the mattress is securely in place at the recommended height to reduce the risk of accidents.
To adjust the crib mattress height for your baby's safety and comfort, follow the manufacturer's instructions provided with the crib. Typically, you can lower the mattress as your baby grows and becomes more mobile to prevent climbing out or falling. Make sure the mattress is securely in place at the recommended height to reduce the risk of accidents.
The Sealy Crib Mattress pad is 100% waterproof.
You would most likely need a crib mattress if you have a small child who sleeps in a crib. You may also need one if you convert to a small toddler bed in which case you could also use a crib mattress.
The Ragazzi Crib 1101 89 is a stylish and functional baby crib featuring a classic design with clean lines and a sturdy construction. It typically comes in a variety of finishes, such as white or natural wood, and includes adjustable mattress heights to accommodate a growing baby. The crib usually has slatted sides for ventilation and visibility, ensuring safety and comfort for your child. Overall, it combines aesthetic appeal with practical features suitable for modern nurseries.
When choosing a lower crib mattress for your baby, consider factors such as firmness, size, breathability, waterproofing, and certifications for safety standards. These factors can help ensure your baby's safety and comfort while sleeping.