answersLogoWhite

0

They are made differently and forged flanges are stronger than plate flanges.

User Avatar

Wiki User

12y ago

What else can I help you with?

Continue Learning about Mechanical Engineering

What is difference between weld neck flange and slip on weld flange?

http://www.tubecraftflange.com/products/slipon.htmTubeSlip-On Flanges are probably the most common type of flanges in the industry and are ideal for lower pressure applications. You do not have to specify the pipe schedule when using slip-on flanges due to the fact that its inside diameter is determined by the outside diameter of the pipe. This outside diameter of the pipe does not change for the different schedules. This often makes these easier to stock for vendors. Fabricators also like the fact that these flanges are slightly easier to align than weld neck flanges. They also are slightly easier to cut pipe to the proper length for. They can be used for high temperature and pressure applications but are not generally recommended as compared to other types of flanges. ASME B16.5 Code limits their usage in the 1500#-2500# (lbs.) weight classes.


What is the different between EH36 and EH36-Z35 steel plate?

Eh-36-35Z is just regular EH-36 plate that has been Impact tested in the "Z" direction at typically -40 F.


What is a swash plate pump?

A swash plate is a way of going from rotary motion to linear motion without using a crankshaft. A swash plate pump is a piston pump that uses a swash plate instead of a crankshaft.


All Thikness IS 2062 ms chequered plate weight with chart?

Any thicknes plate length x with x thicknes x2.1 per plate


What is the unit weight of ms chequered plate?

chequered plate 5 mm thickness weight is 45.4 kg

Related Questions

What is the difference between A105 and A106 gr b?

Vessels are made up of plate materials. A106 is a pipe destination. A105 is a forged material and widely used for flange


What is Max. space between RF-flange faces to insert thick plate. Flange sizes 6 inch and 8 inch?

The maximum space between RF (Raised Face) flange faces to insert a thick plate depends on the specific design and standards used, but typically, it is recommended to maintain a gap of around 1/8 to 1/4 inch to allow for proper alignment and sealing. For 6-inch and 8-inch flanges, the thickness of the plate should not exceed the distance between the flange faces plus any necessary compression or gasket thickness. Always refer to relevant engineering standards and specifications for precise measurements and safety considerations.


Samilarties and differences between volvano and plate tectonics?

Volcanos are mountains in which lava comes out and plate tectonics is the theory of plates moving.


Is there a flange or gasket on side of motor between oil pan and transmission pan on 97 dodge caravan?

There is no gasket between the engine and transmission. The torque converter inspection plate does have a dust seal on it.


What is the difference between a slip yoke and flange yoke on rear of transfer case?

A slip yoke has a splined shaft the drive shaft slides over. This allows the drive shaft to flex on rough terrain. A flange yoke has a flat plate on the transfer case and the end of the drive shaft and they bolt together.


What are the differences between a keyword and a plate?

A keyword is a word or phrase used in a search engine to find relevant information, while a plate is a flat dish used for serving food.


How do you replace the water pump on a 1967 Pontiac 400?

As i recall, the water pump is bolted to the front of the engine block. The cooling fan, is then bolted to a 2" dia. flange, with 4 machine theard (fine) bolts that have 7"/16 There is a plate between the pump and the timing cover, don't forget to reuse that plate. The new pump should come with 2 gaskets, one goes between the pump and plate, the other goes between the plate and timing cover.


What are the key differences between direct and sandwich ELISA techniques?

The key differences between direct and sandwich ELISA techniques are in the way they detect antigens. In direct ELISA, the antigen is directly attached to the plate and detected using a labeled antibody. In sandwich ELISA, the antigen is captured between two antibodies, one attached to the plate and the other labeled for detection.


What is difference between weld neck flange and slip on weld flange?

http://www.tubecraftflange.com/products/slipon.htmTubeSlip-On Flanges are probably the most common type of flanges in the industry and are ideal for lower pressure applications. You do not have to specify the pipe schedule when using slip-on flanges due to the fact that its inside diameter is determined by the outside diameter of the pipe. This outside diameter of the pipe does not change for the different schedules. This often makes these easier to stock for vendors. Fabricators also like the fact that these flanges are slightly easier to align than weld neck flanges. They also are slightly easier to cut pipe to the proper length for. They can be used for high temperature and pressure applications but are not generally recommended as compared to other types of flanges. ASME B16.5 Code limits their usage in the 1500#-2500# (lbs.) weight classes.


What are the differences between prawns and shrimp?

The main differences between prawns and shrimp are their size, anatomy, and habitat. Prawns are typically larger in size, have branching gills, and live in freshwater, while shrimp are smaller, have plate-like gills, and are found in saltwater.


What are the differences between plate tectonic and tectonic plates?

Converging plates come together. They converge together. Diverging plates come apart.


What are the differences between bent axis pump and swash plate pump?

In the bent axis pump,the pistons are at an angle to the drive shaft and thrust plate. The connecting rods are attached to the thrust plate and revolve with it , unlike the swash plate pump where the piston rods slide past a stationary swash plate. In the swash plate pump the rotating shaft and plate are shown in silver.