0
What else can I help you with?
Should angle grinder RPM should be the same with the grinding disc?
The answer is it can be less. Most grinding discs show the maximum RPM allowed, it does not necessarily mean that you have to run at those RPM it means that in order to use the disc SAFELY you should not exceed that speed.
What does RPM ipm sfm stand for in hvac?
in the plumbing world what does SFM IPM RPM stand for
What is the average rpm of an HVAC scroll compressor?
The average RPM of an HVAC scroll compressor typically ranges between 1,500 to 3,600 RPM, depending on the specific application and design. Most residential systems operate around 1,800 to 3,600 RPM, while commercial systems may vary. The exact RPM can influence the efficiency and performance of the compressor in the HVAC system.
How do you calculate angular velocity RPM for lathe when given cut lenght dia workpiece tool pressure and cutting surface speed?
V = Cutting speed N = RPM d = Diameter in millimeters N = 1000.V / d . 3.14
How do you reduce the rpm of a hydraulic motor?
Reduce the output flow of the pump supplying fluid to the motor
What is different between 15K RPM and 7.2KRPM?
The main difference between a 15K RPM (Revolutions Per Minute) and a 7.2K RPM drive is the speed at which the disk spins. A 15K RPM drive spins at a faster rate than a 7.2K RPM drive, resulting in quicker data access and transfer speeds. However, a 15K RPM drive may generate more noise and heat compared to a 7.2K RPM drive.
A typical RPM speed for a PC hard drive?
7200 rpm is quite common.
How do you reduce rpm of an electric motor from 1200 rpm to 240 rpm?
You would use a worm drive meshed with a gear that has 130 teeth.
What is the rpm of a 100 tooth gear that is meshed with a 50 tooth drive gear turning at 200 rpm' s?
To find the RPM of the 100-tooth gear, you can use the gear ratio. The gear ratio is determined by dividing the number of teeth on the driven gear (100 teeth) by the number of teeth on the drive gear (50 teeth), which gives a ratio of 2:1. Since the drive gear is turning at 200 RPM, the driven gear's RPM will be 200 RPM ÷ 2 = 100 RPM. Therefore, the 100-tooth gear will spin at 100 RPM.
What is the rpm supposed to be in drive on the 1997 GMC Sierra V8?
between 650 and 750 in drive
What should the timing be on a 1982 wagoneer with a 360 AMC engine?
10 degrees BTDC @ 600 rpm in drive. high altitude 16 degrees BTDC @ 600 rpm in drive.
How does the diameter of the wheel affect the speed of a car?
It changes the ratio between the engine rpm and the drive wheel(s) rpm.
How can you convert 1400 rpm into 2800 rpm by pully?
To convert 1400 RPM to 2800 RPM using a pulley system, you would need to use a pulley ratio that doubles the speed. This can be achieved by using a smaller drive pulley on the motor (connected to the 1400 RPM source) and a larger driven pulley on the output shaft. The size ratio of the drive pulley to the driven pulley should be 1:2, meaning for every rotation of the drive pulley, the driven pulley makes two rotations, effectively doubling the RPM to 2800.
What is special about a SAS hard drive?
An SAS hard drive has many high performance advantages over a SATA drive. The main thing that makes it better is the speed. A typical SATA drive operates at 7200 RPM, yet a typical SAS drive operates at 10,000 or 15,000 RPM.
What four speed in revolutions per minute might the spindle inside a hard drive rotate?
Common current values are 5400 rpm, 7200 rpm, and 10000 rpm. However 3600 rpm was very common for a number of years.
What are three current ratings for spindle speed for a magnetic hard drive?
Common current values are 5400 rpm, 7200 rpm, and 10000 rpm. However, these are not the only possible values.
If you have motor rpm motor shaft sizeblower pulley size how you get blower rpm?
Drive Pulley = pulley on motor Driven Pulley = pulley on blower First determine your Ratio - divide large pulley size by small pulley size this will give you gear ratio, Example 2" drive pulley and a 4" Driven Pulley = 2:1 gear ratio If you know your motor shaft RPM divide that number by the ratio to get the RPM of the driven pulley, if your shaft rpm is 1800 rpm you would divide 1800 by 2 which would = 900 rpm on your driven pulley if your drive pulley is larger than than your driven pulley you multiply the rpm by the ratio example 1800 rpm x 2 = 3600 rpm
