0
What type of socket is used to turn nuts when a long portion of the bolt or stud protrudes the nut?
Wiki User
∙ 10y ago
Deep or if you can't get one long enough, a box end wrench
Wiki User
∙ 10y ago
Add your answer:
Earn +20 pts
What is the best type of wrench to use on a very tight bolt?
One that fits the bolt very securely, preferably a 'box' wrench, that fits every'flat' and has a long handle to apply maximum pressure to it.
When did the University of the Colorado development new V-engine technology?
A long long long pretty much long time ago
What are the advantages of concurrent engineering?
Manufacturing Personnel are able to identify production capabilities and capacities .They have thus the opportunity to inform the design group about the suitability of certain materials on the flipsides the designer would know the suitability of certain designs in aiding in cost reduction and quality improvement in production/assembly process. Early opportunities for design or procurement of critical tooling, some of which might have long lead times. early consideration of the Technical Feasibility of a particular design or a portion of a design. Again this can avoid serious problems during production.
What is feed engineering?
FEED stands for Front End Engineering Design. It includes robust planning and design early in a project's lifecycle (i.e., the front end of a project), at a time when the ability to influence changes in design is relatively high and the cost to make those changes is relatively low. It typically applies to industries with highly capital intensive, long lifecycle projects. Though it often adds a small amount of time and cost to the early portion of a project, these costs are minor compared to the alternative of the costs and effort required to make changes at a later stage in the project.
What is a long weight?
A long weight is something that an apprentice or new boy is sent to the stores to get. Eg: "go to the stores and get me a long weight for this job" The apprentice dutifully goes to the store-man and asks for long weight where upon the store-man goes away as if to get it returning much later and asks the apprentice "was that a long enough wait?" In other words it is a prank traditionally played on the new and inexperienced employee ! See also: "go and get me a bag of sparks for the grinder" where the apprentice is given an empty but inflated paper bag by the store-man.
What type of socket is used to turn nuts when a long portion of the bolt or stud protrudes through the nut?
Deep Well
How do you replace front blinker bulb on a 2000 Buick LeSabre?
There is a long bolt on top of the headlight/blinker assembly. Remove this bolt and slide the entire headlight/blinker assembly out just enough that you can see the bulb socket. Twist the socket and it will pop right out.
How do you get out the top bolt on a starter on a 1990 Ford super duty diesel?
to remove top bolt you will need a long socket extension bar and a universal joint adaptor.it is a pain to get at but once you have done it it is not so hard in the future so socket to fit bolt,uni joint adaptor,extension bar then ratchet in that order and you will get it
How do you the spark plugs come out on a 2002 Chevy Impala?
if u know were the spark plugs are located use a socket wrench with long socket so you could fit the socket into the hole and do the exact same things as you would do trying to get a bolt free
How do you take the drive clutch off a Polaris trailblazer 250?
Buy a 3"long 3/4"x16 bolt and a 4"long 7/16"x20 socket head bolt at your local hardware store. Thread the 7/16"x20 socket head bolt into the crank until it stops with a 3/8" Allen key wrench. Now thread the 3/4x16 bolt into the clutch. Once it comes in contact with the socket head bolt you will have to hold the clutch from turning. Keep screwing the 3/4" until the clutch comes off the tapered press fit on the crank. Could not be simpler or cheaper.
How can you Loosen the tensioner to replace the serpentine belt?
You look at the bolt holding the tensioner pulley and get a six point socket to fit. Use socket on long bar to rotate tensioner away from belt. Be careful that if socket slips off, personal injury may occur.
How do you remove a starter from a OMC 3.0 sterndrive GM The mounting bolt underneath closest to the engine doesn't seem to have enough clearance around it to get a socket or a wrench on it.?
you need to get a deep socket to get to the small bolt closest to the engine, there are only two bolts that hold on the starters on a 3.0, one is long one is short.
How does a aardvark eat?
It has a very long tongue, which it protrudes from its mouth to slurp up ants and the like.
How does aardvark eat?
It has a very long tongue, which it protrudes from its mouth to slurp up ants and the like.
How do you take out the harmonic balancer bolt on a 1965 mustang?
Put a long breaker bar on socket that fits onto the harmonic balancer bolt then disconnect the main coil wire so the engine will not start. Now gently turn the long breaker bar on the bolt like you are trying to take it out. When the breaker bar hits the floor get into the car and turn the starter motor and like majic the bolt will come loose.
What is the definition of Bacteria Flagellum?
A flagellum is a long tail like structure that protrudes off the bacterium body.
How do you replace front hub assembly on a 2000 bravada?
2000 olds bravada you need a 36 mm socket / half inch drive and a breaker bar with it. roughly 35-40 dollars.I believe a 18mm socket also . Take the wheel off . take something to knock off the aluminum cap in the center . take bolt off w/the 36 mm socket. . there are 4 bolts on the back-side of the break . take one out of the top first. if it is a long bolt with a funny looking end on it , bingo you have the right bolt . If not replace that bolt and try again .only 2 bolts hold this on . you my have to pry the breaks off the rotor with screw driver but you want hurt anything doing this..;put it all back together the way you took apart . It's easy if you have the tools. ( One bolt will be impossible to get to with a socket ) it's the one on top. and you will need an open ended wrench or your out of luck. ............one wrench, one socket the same size.think its 18 mm or 16.and one 36 mm socket with breaker bar, it's on TIGHT.
