answersLogoWhite

0

Most motors on swamp coolers have an "automatic reset thermal overload". So while your cooler will run, you'll have to keep climbing up on the roof to adjust it after it cuts out every 15 minutes. Obviously this isn't the best way to go about it. The instructions for your motor should be available online to help you figure out the correct tension. It's always best to get it right the first time but sometimes it can wind up as trial and error. I installed my motor, pump, belts, etc by watching YouTube videos. My husband usually causes more harm than good so I generally install the hot water heaters, Plumbing, masonry, cooler maintenance, etc and leave him to do the dishes! Sometimes it's hard because they expect you to have all the fancy tools for measuring the tension but if in doubt, hire the next door neighbor's landscaper to do it for you! I generally just have to flirt to get him up there but you might have to throw a couple bucks their way if you're a male!

User Avatar

Wiki User

12y ago

What else can I help you with?

Related Questions

What are the common issues that can arise with a swamp cooler motor and how can they be resolved?

Common issues that can arise with a swamp cooler motor include overheating, motor failure, and lack of proper ventilation. These issues can be resolved by ensuring proper maintenance, such as cleaning the motor and fan blades regularly, checking for any obstructions in the ventilation system, and replacing worn-out parts as needed.


How do you replace the bearings in your swamp cooler?

replacement bearing cooler


Swamp Cooler Installation?

form_title=Swamp Cooler Installation form_header=11553 Please specify the type of space the swamp cooler will be used in.*= () "Single Family Home () Mobile Home () Garage, warehouse, etc." Where would you like the swamp cooler installed?*= () Roof () Wall () Window () Attic Can you explain how the swamp cooler will be regulated?*= () On/off switch () Thermostat () Want recommendation What number of rooms would you like the cooler to be connected to?*= {Select One,1,2,3,4,5,6,7,8,9,10 or more}


Is a desert cooler or a swamp?

A desert is cooler because of the loneliness outside


How do you get mold out of your swamp cooler?

Put a lot of copper pennies in your swamp cooler. The copper will kill the mold using IONs or something.


You are looking for swamp cooler motor Model K55HXJBR-8989?

The K55HXJBR-8989 is a specific model of swamp cooler motor commonly used in evaporative coolers. To find one, you can check with local HVAC supply stores, online retailers, or websites specializing in replacement parts for swamp coolers. Additionally, consider contacting the manufacturer directly or looking for compatible alternatives if the exact model is unavailable. Always verify the specifications to ensure compatibility with your unit.


If you have an Emerson motor for an Arctic Circle swamp cooler model k55hxjbr8989 1 8 hp 115v 60hz 1 phase rpm 1075800 where can you find a replacement motor?

To find a replacement motor for your Arctic Circle swamp cooler model K55HXJBR8989, you can check with local appliance repair shops or HVAC suppliers that specialize in swamp cooler parts. Additionally, online retailers such as Amazon, eBay, or specific HVAC parts websites may have compatible Emerson motors available. Be sure to verify the specifications to ensure compatibility with your unit. If you're unsure, contacting the manufacturer or a professional technician for assistance might also be helpful.


Do Home windows have to be open when using a swamp cooler?

Home windows do have to be open when you are using a swamp cooler. You do not open them all the way, they should be opened part way.


Swamp cooler leak?

the best thing for a swamp cooler leak, is a copper pipe, or plumbing sealant, its similar to jb weld, only its waterproof, and made for leaks.


How much water does a swamp cooler use?

A swamp cooler can use anywhere from 3 to 15 gallons of water per day, depending on factors like humidity levels and desired cooling effect. It is important to regularly monitor and replenish the water in the swamp cooler to ensure its effectiveness.


Is evaporation in the swamp cooler a physical change?

Yes, evaporation in a swamp cooler is a physical change. It is the transition of water from liquid to vapor state without changing its molecular structure.


What metal is a swamp cooler made of?

Swamp coolers, also known as evaporative coolers, are typically made of galvanized steel, aluminum, or plastic. These materials are used for their durability and ability to withstand exposure to water and moisture in a swamp cooler's operation.