answersLogoWhite

0

Watch the YouTube video.

User Avatar

Wiki User

8y ago

What else can I help you with?

Related Questions

How do you string a dual line remington trimmer?

It is easy to string a dual line Remington trimmer by following the instructions in the manual. The manual was supplied with the trimmer when purchased.


How do you feed line into maruyama trimmer bt23l?

To feed line into a Maruyama BT23L trimmer, first, turn off the trimmer and detach the cutting head. Remove the spool from the head, then feed the trimmer line through the eyelet in the spool, leaving equal lengths on both sides. Wind the line in the direction indicated on the spool, ensuring it is neatly coiled without overlapping. Finally, replace the spool into the head, making sure the line is properly seated in the eyelets before reattaching the head to the trimmer.


What is the best method for replacing the weed trimmer line on a string trimmer?

To replace the weed trimmer line on a string trimmer, follow these steps: Turn off the trimmer and disconnect the power source. Remove the spool housing by pressing the tabs or unscrewing the cap. Take out the old line and cut a new piece to the appropriate length. Insert the new line into the trimmer head following the arrows for the correct direction. Reassemble the spool housing and test the trimmer.


How can I restring a Ryobi string trimmer?

To restring a Ryobi string trimmer, first remove the spool from the trimmer head. Cut a length of new trimmer line, thread it through the holes in the spool, and wind it evenly around the spool. Reinsert the spool into the trimmer head, and feed the line through the trimmer head eyelets. Finally, secure the spool back in place and trim any excess line.


How do I perform a Ryobi trimmer string replacement?

To perform a Ryobi trimmer string replacement, first turn off the trimmer and disconnect the spark plug. Remove the spool cover and take out the old string spool. Cut a new piece of trimmer line to the appropriate length and insert it into the spool. Wind the new line evenly onto the spool in the direction indicated on the spool. Reassemble the trimmer and test the new string before use.


What is the purpose of a line trimmer?

A line trimmer, also known as a string trimmer, is used to trim grass or weeds. The piece of equipment also goes by the name of a weed eater, or weed whacker.


Installing cutter string bolens bl150 trimmer?

To install the cutter string on a Bolens BL150 trimmer, start by ensuring the trimmer is turned off and unplugged for safety. Remove the spool from the trimmer head by pressing the tabs on the sides and pulling it out. Cut a length of new trimmer line, typically around 10-15 feet, then thread one end through the eyelet on the spool, winding it around the spool in the direction indicated by the arrows. Finally, reattach the spool to the trimmer head, ensuring the line is properly fed through the eyelet before securing it in place.


How do I reload the line on my Ryobi string trimmer?

To reload the line on your Ryobi string trimmer, first remove the spool from the trimmer head. Cut a length of new trimmer line, usually around 10 feet, and insert one end into the spool's center hole. Wind the line evenly and tightly around the spool in the direction indicated on the spool. Leave a few inches of line unwound, then thread the line through the trimmer head's eyelet. Reassemble the spool onto the trimmer head, ensuring the line feeds through the head properly.


Install new line on HomeLite TrimLite weed trimmer?

pray


How to install trimmer line properly?

To install trimmer line properly, first, make sure the trimmer is turned off and disconnected from power. Then, remove the spool housing and take out any remaining old line. Cut a new piece of trimmer line to the appropriate length and insert it into the spool, following the arrows for the correct winding direction. Finally, reassemble the spool housing and trim any excess line.


How do you refill a Ryobi string trimmer?

To refill a Ryobi string trimmer, you need to first turn off the trimmer and remove the spool cap. Then, take out the empty spool and replace it with a new one, making sure to wind the trimmer line in the correct direction. Finally, reattach the spool cap and you're ready to trim again.


How do you pull more string out of trimmer?

This is actually easier than it first appears. # Line up the two arrows on the outer-spool and inner-reel. # ## This opens the channels from the feed-holes to the locking holes. # Remove any line left in the locking holes. # Feed new line into feed holes up though the channels until you have enough to place the ends of the lines into the locking holes. # Place line ends into the locking holes and pull tight. # Wind the inner-reel counter-clockwise, taking up the new line. Pause occasionally to pull each line tight. Leave about 4 inches at each end.