0
What else can I help you with?
What is the fuel ratio for a homelite hlt25cs line trimmer?
50:1
How do you repair pull cord on homelite trimmer?
The pull cord on a Homelite trimmer is repaired by removing the outer cover and pulling out the cord spool. A new line is then attached, wound around the spool, and put back in place.
Homelite string trimmer?
Homelite string trimmers are inexpensive brand that you can probably buy at home depot. Depending on how much trimming you have to do in your lawn, should help you decide on how much you want to put down on a trimmer. I suggest going with a Stihl trimmer or a Poulan Pro. You can probably find a bottom of the line residential unit from these brands for about what you would pay for a homelite maybe a few dollars more, but worth it.http://www.weedwackerstore.com
How do you string a homelite trimlite ut20004a weed trimmer?
Best bet, do what I did....and don't! go to Home Depot and get one of those Rhino products that you take the string attachment off and bolt this baby one. Works great and does away with the bump and feed. You just put a 12 in. line of your choice of thickness by pressing a button and feeding the 12 inch line through. That is all there is. You might have to replace that 12 inch line after each use but I put in really thick line and if works for about an acre of land. Very pleased for a product that cost me $15.00 and just bolts on to the end of the Homelite shaft.
How do you install line on maruyama string trimmer?
Watch the Youtube video.
How to install trimmer line properly?
To install trimmer line properly, first, make sure the trimmer is turned off and disconnected from power. Then, remove the spool housing and take out any remaining old line. Cut a new piece of trimmer line to the appropriate length and insert it into the spool, following the arrows for the correct winding direction. Finally, reassemble the spool housing and trim any excess line.
What is the fuel mixture ratio for a homelite trimmer model z725cdv?
Most trimmers roughly 5 oz per gallon gas. The bottles they sell next to the line are to treat 1 gal typically.
How do I replace the line on a Ryobi RY15523A trimmer?
To replace the line on a Ryobi RY15523A trimmer, follow these steps: Turn off the trimmer and disconnect the spark plug wire. Remove the spool from the trimmer head. Cut a length of replacement trimmer line. Insert the line into the trimmer head following the arrows for the correct direction. Wind the line evenly and tightly onto the spool. Reassemble the spool onto the trimmer head. Reconnect the spark plug wire and test the trimmer.
How do I replace the line on my Ryobi gas trimmer?
To replace the line on your Ryobi gas trimmer, first remove the spool cover and take out the old line. Cut a new piece of trimmer line to the appropriate length and insert it into the spool. Wind the line evenly and securely onto the spool, then reassemble the trimmer.
How do you string a dual line remington trimmer?
It is easy to string a dual line Remington trimmer by following the instructions in the manual. The manual was supplied with the trimmer when purchased.
How can I change the trimmer line on my trimmer?
To change the trimmer line on your trimmer, first, turn off the trimmer and disconnect it from the power source. Remove the spool housing by pressing the tabs on the sides. Take out the old trimmer line spool and replace it with a new one, following the arrows for the direction of the line. Cut the line to the desired length and feed it through the holes in the spool. Finally, reassemble the spool housing and you're ready to trim.
What is the best way to replace the weed wacker line on a trimmer?
To replace the weed wacker line on a trimmer, first, turn off the trimmer and disconnect the power source. Then, remove the spool housing and take out the old line. Cut a new line to the appropriate length and thread it through the trimmer head following the arrows. Finally, secure the line in place and reassemble the trimmer.
