0
What else can I help you with?
Can you jump a motorcycle battery with a car battery?
yes, you can. BUT don't start the car! just connect the jumper cables from car to motorcycle wait 5 minutes and then try to start the motorcycle.
How do you wire a motorcycle amp to the motorcycle?
To wire a motorcycle amp to your motorcycle, first disconnect the battery to ensure safety. Next, connect the amp's power wire to the motorcycle's battery, usually via the positive terminal, and attach the ground wire to a clean, bare metal surface on the frame. Then, connect the speaker wires from the amp to the motorcycle's speakers, ensuring proper polarity. Finally, reconnect the battery and test the amp to ensure everything is functioning correctly.
Where is the vin located on a 2007 Honda CBR motorcycle?
Honda has a tendency, just like most motorcycle manufacturers, to place the VIN in the area of the front forks, around where the forks "connect" to the body of the motorcycle.
How do you connect the battery to the coil to start a honda cd175 engine out of the frame and on the bench?
Just connect the battery to the motorcycle battery cables with jumper cables and then start it.
How do you get a list of the names of motorcycle clubs?
To obtain a list of motorcycle clubs, you can start by searching online directories and forums dedicated to motorcycle enthusiasts. Websites like the Motorcycle Safety Foundation or local motorcycle shops often have resources or community boards that list clubs. Additionally, social media platforms can be useful, as many clubs have pages or groups where they promote their activities. Finally, attending motorcycle events or rallies can provide opportunities to connect with clubs directly.
Can scorpins jump?
yes then can jump as when they sting they jump to make the sting connect :)
How do you jumpstart r1200c?
To jumpstart a BMW R1200C motorcycle, first ensure you have a proper jump starter or another vehicle with a charged battery. Connect the positive (red) jumper cable to the positive terminal of the motorcycle battery, then connect the other end to the positive terminal of the donor battery. Next, attach the negative (black) cable to the donor battery's negative terminal and the other end to an unpainted metal surface on the motorcycle frame for grounding. Start the donor vehicle, then attempt to start the R1200C; once it starts, disconnect the cables in reverse order.
How to recharge a motorcycle battery?
Connect the positive clip of the battery charger to the positive terminal on the battery. Connect the negative clip of the battery charger to the negative terminal on the battery. Select the charge rate you desire either 2,4, or 6 amp. The newer battery chargers will let you know when it is fully charged.
How do you Check motorcycle Battery Amps?
To check a motorcycle battery's amps, you can use a multimeter. Set the multimeter to the DC amps setting and connect the red probe to the positive terminal and the black probe to the negative terminal of the battery. Make sure the motorcycle is off, and take note of the reading; it should display the current flowing through the battery. For a more accurate assessment of battery health, consider performing a load test with a dedicated load tester.
Which circuit would have the brightest light?
If you connect bulbs in parallel across a given voltage supply (eg household mains supply) then they will all draw their rated current and will glow at their rated brightness. If you connect the same bulbs in series then they will glow very much less brightly. This is because the resistance of a bulb's element is also related to the power dissipated in the element. A bulb's element is rated for operation at a particular voltage. You can certainly connect two 6v motorcycle bulbs in series, and connect them to a car battery at 12v, and the two bulbs will be just as bright as they were when individually operated from the motorcycle 6v batttery. However if you connect two 6v bulbs in parallel and then wire them to a 12v car battery they will only glow brighter for a fraction of a second and then ... pop. You will have overheated the elements beyond their designed power handling capability.
How do you polarize a Harley Davidson generator?
To polarize a Harley Davidson generator, first ensure the motorcycle is off and the battery is disconnected. Then, briefly connect a jumper wire from the positive terminal of the generator's armature terminal to the positive terminal of the battery. This action polarizes the generator, aligning the magnetic fields correctly. Finally, reconnect the battery and start the motorcycle to check for proper charging.
Where is the best place to sell my antique motorcycle?
The best place to sell your antique motorcycle is through specialized online platforms like Bring a Trailer or Hemmings, which cater specifically to enthusiasts and collectors. You can also consider auction houses that specialize in vintage vehicles, as they can attract serious buyers. Additionally, local motorcycle clubs or shows might provide opportunities to connect with potential buyers directly. Lastly, social media groups dedicated to antique motorcycles can also be effective for reaching interested audiences.
