0
What else can I help you with?
Is there another exhaust system that can be used for a 1983 Yamaha Virago 535?
jardine rumblers
What is the valve clearance on a 1983 Honda XR500?
0.05mm
What is the valve clearance for 1983 suzuki lt125?
What is the valve clearence for a 1985 lt 125
Where is oil dipstick located on a 1983 Yamaha virago 750?
There is no dipstick. It's a site guage located on the left side of the bike.
Are parts like the motor from my 1983 Yamaha xv 500 interchangeable with a 1985 Yamaha 700 Virago frame?
The motors from a 1983 Yamaha XV 500 and a 1985 Yamaha Virago 700 are not directly interchangeable due to differences in engine design, mounting points, and overall frame compatibility. While both bikes belong to the same family of Yamaha Viragos, variations in engine size and specifications mean modifications would likely be necessary. It's essential to consult specific technical resources or forums dedicated to Yamaha motorcycles for detailed compatibility insights before attempting any swaps.
How much oil in a 1983 Yamaha virago 500?
The 1983 Yamaha Virago 500 typically requires about 2.5 quarts (approximately 2.4 liters) of oil when changing the oil and replacing the oil filter. If you're just changing the oil without replacing the filter, it may take around 2.0 quarts (about 1.9 liters). Always consult the owner's manual for the most accurate specifications.
What is the valve clearance of a 1983 Mazda B2200 diesel engine?
the valve lash for a 1985 Mazda 2.2 diesel is .012 in under cold conditions
What is Valve clearance on 1983 suzuki lt 125?
The valve clearance for a 1983 Suzuki LT 125 is typically set between 0.05 mm (0.002 inches) and 0.08 mm (0.003 inches) for both the intake and exhaust valves. It's important to check and adjust the valve clearance periodically to ensure optimal engine performance and prevent potential damage. Always refer to the service manual for the most accurate specifications and procedures.
How do you do valve adjustment on 1983 Nissan Datsun 200sx?
To adjust the valves on a 1983 Nissan Datsun 200SX, first ensure the engine is cold. Remove the valve cover and use a feeler gauge to check the clearance between the rocker arm and the valve stem for each cylinder. Adjust the clearance by loosening the lock nut on the rocker arm and turning the adjustment screw until the correct clearance is achieved, then retighten the lock nut. Repeat this for all cylinders, then reassemble the valve cover.
How many turns out should the pilot screws be on a 1983 Yamaha Virago 750?
The optimal setting for a pilot screw on almost any bike is one and one half full turns out from the closed position.
How do you remove 1983 virago gas tank?
To remove the gas tank from a 1983 Yamaha Virago, start by ensuring the motorcycle is on a stable surface and the fuel is drained. Disconnect the fuel lines from the petcock and any vacuum lines. Then, remove the bolts securing the tank to the frame, typically located under the seat or at the rear. Finally, lift the tank off carefully, ensuring to avoid damaging any attached components.
How do you adjust the valves on a 1983 Nissan 280ZX?
To adjust the valves on a 1983 Nissan 280ZX, first, ensure the engine is cold. Remove the valve cover and locate the rocker arms. Using a feeler gauge, check the clearance between the rocker arm and the valve stem; it should be set to the specifications outlined in the service manual (typically around 0.008 inches for intake and 0.010 inches for exhaust). Adjust the clearance by turning the adjusting nut on the rocker arm until the desired gap is achieved, then recheck with the feeler gauge and reassemble the valve cover.
