0
What else can I help you with?
What is the input choke used for AC drive. What is its function?
The function of the input choke for an AC drive is much the same as the function of the choke on any other mechanical device. The jump start the unit the choke should be in the open mode. The stop the operation of the unit the choke should be moved to the closed position.
How do you know if choke is open or closed?
To determine if a choke is open or closed, you can visually inspect the choke mechanism. In a closed position, the choke plate will be nearly perpendicular to the airflow, restricting it, while in the open position, the plate will be parallel, allowing air to flow freely. Additionally, many engines have a choke indicator or a lever that shows its status. If the engine is running rough or struggling to start, it may indicate that the choke is closed when it should be open.
How do you start a Harley Davidson 883 sportster?
turn key to start position, put bike in neutral, ( one position up from first gear), neutral light should light and push start button. If engine is cold pull out choke cable on left side.
How do you start a McCulloch chainsaw?
Don't know what model you have but mine starts this way: start switch to on ..throttle in lock start position..choke out...pull three times...push choke in and pull to start...mine starts every time this way...
I can start THE car after setting over nigth. after it runs and you shut it off it won't start again 1981 280z?
Your choke may be stuck in the closed position , there for after the car is warm it want start because it no longer requires the choke . It's something to check .
How do you start an ATV?
make sure its in neutral, set hand brake and turn the key to on position and press start buttun. you may have to set the choke
How do you start a Weed eater Featherlite?
COLD ENGINE STARTING OR STARTING AFTER REFUELING --Set unit on a flat surface. --Slowly press the primer bulb 6 times. --Move choke lever to FULL CHOKE position. --Squeeze the throttle trigger fully and hold through all remaining steps. --Pull starter rope handle sharply 6 times. --Move choke lever to HALF CHOKE position. --Pull starter rope handle no more than 6 pulls, until engine runs. --Allow engine to run 10 seconds, then move choke lever to OFF CHOKE position. RESTARTING A WARM ENGINE --Move choke lever to OFF CHOKE position. --Pull starter rope handle until engine runs. --If engine does not start in 5 pulls, follow instructions in STARTING A COLD ENGINE.
How do you get a 50cc quad started?
To start a 50cc quad, first ensure it's in neutral and the kill switch is in the "on" position. Turn the ignition key to the "on" position, then pull the choke lever out if the engine is cold. Press the electric start button or use the kick start if applicable. Once it starts, gradually push the choke back in as the engine warms up.
85 Chevy 350 wont start with choke?
does it start without the choke? if it does you are probably flooding the engine with the choke readjust it
Why would a 2 cycle engine not start?
== == Basically, the problem is often that, the choke being left "on" continually prevents the engine from starting because there is too much gas for the air being provided. (The choke control reduces the air being provided to burn with gas). On warm days, a two-cycle engine does not need to be choked very much. The cooler it is, the longer you need to leave the choke on. You need to prime the engine by pushing in on the plastic dome that you can see gas in. That sends gasoline into the fuel line. Five pumps or so is all you need. Be sure that the cut-off switch is turned to "run". Put the choke lever into "choke on" position. Pull the start cord twice. That normally provides a good gas/air mixture to the cylinder. If the engine starts, put the choke lever back into the "choke off" position after a few seconds, and let the engine warm up. If it starts to sputter, put the choke back on for a few seconds more. If it doesn't start, put the choke lever back in the "choke off" position. (Yes, even if the engine does not start). Continue to pull the starter cord several more times. then put the choke lever back to "choke on" if it still won't start and start the cycle again.
How do you use manual choke generac portable generator?
To use the manual choke on a Generac portable generator, first ensure the generator is on a stable surface and the fuel tank is filled. Set the choke lever to the "choke" position to restrict airflow, which helps start the engine when it's cold. After starting the generator, gradually move the choke lever to the "run" position as the engine warms up. Always refer to the owner's manual for specific instructions related to your model.
Do you prime the engine after your snowblower runs out of gas?
Yes, you should prime the engine after your snowblower runs out of gas, especially if it has a primer bulb. Priming helps to draw fuel into the carburetor, making it easier to start the engine again. After running out of gas, it’s important to refill the tank with fresh fuel and allow the primer bulb to fill the carburetor before attempting to start the snowblower. This ensures proper fuel flow and smooth operation.
