0
What else can I help you with?
How do you reset the tire pressure indicator light on a Dodge Journey .we have no manual?
To reset the tire pressure indicator light on a Dodge Journey without a manual, first ensure that all tires are properly inflated to the recommended pressure. Then, turn the ignition to the "On" position without starting the engine. Press and hold the tire pressure monitoring system (TPMS) reset button, typically located beneath the steering wheel or near the fuse box, until the indicator light blinks and then turns off. Finally, drive the vehicle for a few minutes to allow the system to recalibrate.
Why would all speeds work on the fan except for 5 in your 2005 trailblazer And also now your headlights flickerdim at night faintly?
Could be the blower motor resistor. If the other fan speeds start to disappear over time then you will have to buy the resistor. Cheap and easy fix in 20 minutes. Headlights flickering are probably an indicator that your battery is getting weak. www.trailvoy.com All the answers for your Trailblazer with pictures and instructions!
Where is the blower motor resistor on a 1998 f-150?
The blower motor resistor is located under the front dash on the passenger side of the truck. It is a fairly simple job to replace...maybe 15 minutes. The blower motor resistor is located under the front dash on the passenger side of the truck. It is a fairly simple job to replace...maybe 15 minutes.
How do you run flat indicator and reset on b200?
To run the flat tire indicator and reset it on a Mercedes-Benz B200, first ensure that the vehicle is in a stationary position. Then, access the vehicle's dashboard menu using the controls on the steering wheel or the central display. Navigate to the tire pressure monitoring section, select the option to reset the tire pressure, and confirm the reset. After that, drive the vehicle for a few minutes to allow the system to recalibrate.
Can you use a 100 watt metal halide bulb in a 150 watt lamp?
Not recommended. It would work but shorten lamp life and may cause risk of fire. However, if you just wanted to check a lamp was capable of striking it would be ok for a few minutes. I've done the opposite in the past and used a 150w lamp with a 100w ballast. Works, but not good for any of the components, including lamp.
How do you replace a blower motor resistor in a 1999 dodge grand caravan?
Just did it. The resistor is behind the passenger strut in the fire wall. Remove the wire from the old resistor, pull out the old resistor (held in by clips in the device. Install the new unit and re-attache wire. The space is tight and should not take you more than 30 minutes.
On a 1995 olds aurora Secutiy lamp indicator flashing and won't turn over then stays on driver info screen reads clean key on wait 3 minutes I do that and same thing happens any ideas?
Maybe a bad resistor on the key Maybe a bad reader in the ignition Hopefully you have another key to try
What is the labor time for a blower motor resistor on a Chevy Trailblazer?
About 15 minutes. Easy and simple. Read all about it at www.trailvoy.com
How do you check the sleep mode on a 2003 BMW X5?
If it is equipped with the automatic transmission - the "P" indicator on your gear selector will remain lit for 16 minutes after shutdown. After the 16 minutes has passed, you'll notice the lamp has gone out. That is your indicator that the vehicle has entered "sleep" mode (when the light is out).
Is brisk walking for 45 minutes is an indicator of good heart condition?
Yes. 100% true if you walk briskly for 45 minutes daily for five days a week.
How long does it take to pressure can tomatoes?
It typically takes about 85 minutes to pressure can tomatoes.
How do you replace the blower resistor on a 2000 Mercury Cougar?
On the passenger side of the vehicle, under the dash is the blower moter, there are two wires running from it, the one running to the resistor is mounted on the firewall. you remove the two screws with a star shaped screw driver, unplug the old resistor and plug in the new one...takes about 15 minutes.
