Typically yes, but not always: you can also measure the voltage between any two points in a circuit to determine the voltage difference between those two points. It all depends what you are trying to find out about the circuit.
Another example of a voltage that is not referenced to ground is the phase-to-phase voltage in a 3-phase electrical service.
<><><>
As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.
Before you do any work yourself,
on electrical circuits, equipment or appliances,
always use a test meter to ensure the circuit is, in fact, de-energized.
IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS.
Zero Volts, Ground, or Earth. All current flows to this. It stand for NO POTENTIAL. A ground can be elevated to 100v that is the return for that particular circuit sitting 100 volts from earth.
In a parallel circuit, all the branches are joined together at their start and again at their end by a conductor (usually wire).Now, the surface of a conductor (ideally) is an equipotential surface. That is, any point of its surface has the same electric potential.And since the voltage across each branch equals the difference in electric potentials between its start and its end, and these potentials are the same for every branch, it follows that the voltages across each branch must be equal to each other.
complex circuit
When all parts of a circuit are composed of conducting materials, the circuit is said to be closed. One condition could be a closed circuit, however it could be open if the components are not assembled or are assembled incorrectly.
demodulator circuit is a circuit which is used for remove all high frequency components from modulated signal.
That is a series circuit, all parts have the same current flowing through, and the voltages add up.
It all depends on what you are trying to achieve or measure. To find spot voltages around a circuit, it is normal to measure with reference to a common rail or ground. Attach one lead (normally black negative) to a common ground, chassis or negative point, then probe with the red lead to check spot voltages at test points. If you are permanently rigging a voltmeter in a circuit, it is usually there to monitor power supply voltage. It should be wired across the output of the power supply or across a battery. ie connected directly to the poles.
First of all, in an active circuit, there are voltages flowing through various nodes. If you try to measure the resistor, those voltages will cause error in your meter, or may damage your meter. Second of all, even if you cut the power, any loop in the circuit around the resistor will affect the measured impedance. Unless you are certain that only the resistor will see the current introduced by the meter, you must take the resistor out of circuit to measure it.
-- The current in each individual resistor is (voltage across the whole circuit) divided by (the resistance of the individual resistor). -- The current in any individual resistor is less than the total current in the circuit. -- The total current in the circuit is the sum of the currents through each individual resistor.
the same In a parallel circuit, the voltage travels through all the closed circuit paths. They are not branches.
A ground (earth) wire is needed in not just a light circuit but in all circuits that are now installed.
A short circuit condition is caused by the grounding of the circuit anywhere from the distribution point to the load of a circuit. This grounding causes a high rush of current because of a low resistance of this type of circuit. This high rush causes the over protection device to trip and interrupt the current flow.
"Ground" is an important concept in electronics and it has practical significance. Ground provides a reference from which all other voltages are "measured". It is generally held a zero volts. Ground comes from the old nomenclature of "earth ground" and sometimes it is still referred to as "earth". Occasionally, you will see "chassis ground". Chassis ground refers to the voltage of the electronics chassis, which sometimes is isolated from earth ground and there may be (usually there is) a voltage differential between earth ground and chassis ground. The intent of most three prong plugs is to keep the chassis ground the same voltage as earth ground. If this were not the case, there could be the potential (pun intended) of a nasty shock.
A direct short to ground or an overloaded circuit.
A: When all circuit do not exactly tie into a common point. This situation is called daisy chain whereby a ground will add or subtract to influence all circuitry's
In a series circuit, the voltage is divided among the components, so the highest voltage is at the beginning of the circuit. In a parallel circuit, each component receives the full voltage of the source, so the voltage is the same across all components. Therefore, the circuit with the highest voltage would be in a series circuit.
If a circuit shorts to ground before the load, it will create a path of least resistance for the current to flow directly to ground instead of through the load. This can cause excessive current to pass through the shorted section of the circuit, potentially leading to overheating, equipment damage, and circuit failure. It can also cause the load to not operate as intended or not receive power at all.