Bounded strain gauges are designed to operate within a specific range of strain, providing accurate measurements only within that limit, while unbounded strain gauges can theoretically measure strain without a predefined limit, allowing for broader applications. Bounded gauges typically feature a protective element that restricts their range, ensuring reliability and precision under controlled conditions. In contrast, unbounded strain gauges may be used in scenarios where extreme strains are expected, though they may sacrifice some accuracy and stability. The choice between the two depends on the application requirements and the expected strain conditions.
The Andromeda strain is what is known as sweet sciency magic.
No Soul No Strain was created in 415.
The Deviant Strain was created in 2005.
Ferine means wild; untamed. Strain used with ferine means song. So ferine strain is 'wild song'.
The rough strain of bacteria is non-virulent and does not cause disease, while the smooth strain is virulent due to its protective capsule. When the heat-killed smooth strain was introduced to the mice, it released its genetic material, which could be taken up by the rough strain through a process called transformation. This allowed the rough strain to acquire the virulence factors from the smooth strain, making it capable of causing disease and ultimately killing the mice. This phenomenon demonstrated the principle of bacterial transformation and the transfer of genetic traits.
there is no difference
difference between Strain-stress diagram of copper and steel?
Strain is the measure of length change per unit length. Elongation usually refers to strain under load at failure point.
The essential difference is that the bonded strain gauges are bonded on to the specimen whose strain is being measured whereas the unbonded strain gauges are not bonded on to the specimen. As the bonded strain gauges are well bonded on to the specimen, the entire strain being experienced by the specimen is transferred to the strain gauge. However, the bonded strain gauges are affected by temperature changes and also due to transverse strains.For transverse strains and ambient temperature compensations, suitable circuits for compensation can be used using Wheatstone's bridge. The unbonded strain gauges cannot transfer the strain of the specimen to the strain gauge and hence it is used mainly for displacement, or pressure or force transducers. It is least affected by transverse strain and temperature compensation of unbonded gauges cis automatically eliminated using Wheatstone's bridge.
Strain gage and Extensometer both are same purpose to check the stress and strain in selective test pieces, but traditional they were using strain gage its take the preparation time is high and Extensometer we are check the directly both results are same.
Strain aging could be described as " normal wear and tear " or the fatigue that is experienced under normal conditions, whereas Dynamic strain would be an out of the normal range stress condition like a one time over stress condition where the sum of much strain aging is experienced in one " dynamic" occurrence.
An old strain of DNA refers to the original sequence of genetic code, while a new strain refers to a mutated or altered version of the DNA. Mutations in the DNA sequence can lead to differences in characteristics or functions of an organism.
The normal strain is a deformation caused by normal forces such as Tension or Compression that act perpendicular to the cross-sectional area, while the shear strain is a deformation obtained from forces acting parallel or tangential to the cross-sectional area.
We knew from Hook's law- "stress is proportional to strain." So, stress = k * strain [here, k is a constant] or, stress/strain= k Now, if the stress and strain occurs due to axial force then k is known as modulus of elasticity and it is denoted by E. if the stress and strain occurs due to shear force then k is known as modulus of rigidity and it is denoted by G.
NO, You misunderstand the definitions. A sprain affects a joint and a strain affects a muscle E.G. I sprained my ankle and strained my calf. NO, You misunderstand the definitions. A sprain affects a joint and a strain affects a muscle E.G. I sprained my ankle and strained my calf.
A strain is an overstretched or "pulled" or torn muscle. a sprain is an overstretched or torn ligament (holds bones together at a joint), and a fracture is a crack, chip, break or crush of a bone.
Some people mean the same thing when they talk about repetitive strain injuries and repetitive motion injuries. The difference is most likely that RSIs are from abusing a part of your body by working it improperly while a RMI is just from regular use.