Most cars have a switch to disable the cruise control. To permanently disable the cruise, remove the fuse for the circuit.
If the engine on the Santa Fe is missing, then the cruise control will not operate properly. The engine will have to run properly before the cruise can be fixed.
If you have a manual transmission the stop button on the clutch switch may have broken apart, replace the stop button to fix the cruise control. You can get one at any Nissan Dealership.
HBO First Look - 1992 The Making of 'Speed 2 Cruise Control' 4-2 was released on: USA: June 1997
basic cruise control but the speed maintained is controlled by radar sensors. the car decelerates when a slower vehicle pulls in front and the accelerates when the road is clear. ANSWER: above is not quite right it does provide a safety margin of distance from an object. I will accelerate but only to the previous set speed.
the abs/asc (automatic speed control) fuse in the driver kick panel.it is 5 amp fuse third one down from top.works abs & speed control (cruise).this is my guess but not totally sure. I checked all the fuses on mine; all were good. I removed 3 - 5/16" nuts & removed engine cover (top). Found the end of the cruise control cable connector (cheap plastic) had worn through, letting it separate from the throttle stub it connects to. (No cable hooked up?, cruise won't work) I put the connector back on the throttle knob, drilled a small hole in the end of the plastic connector & dropped in a small clip pin (a small cotter pin will work too) in to lock the plastic piece & prevent it from sliding off during acceleration. This in no way affected linkage, etc. & holds the cruise cable connector to the throttle where it belongs. Check this, it's easy to find, & might save you the $40 for a new cruise cable. I have pictures if you need the fix. Good Luck
no
To fix the cruise control on a Corvette, first check the fuse associated with the cruise control system and replace it if necessary. Inspect the cruise control module and related components for any signs of damage or disconnection. If the system still doesn’t work, consider examining the brake switch, as a malfunction there can disable the cruise control. If issues persist, consulting a professional mechanic or referring to the vehicle's service manual for troubleshooting guidance is recommended.
To fix the cruise control on a 2001 Ford Windstar, start by checking the fuse related to the cruise control system and replacing it if it's blown. Next, inspect the cruise control switch on the steering wheel for any damage or malfunction. Additionally, examine the brake pedal switch, as a faulty switch can disable the cruise control. If these steps don't resolve the issue, consider consulting a professional mechanic for further diagnostics.
Are your break lights working? Not sure, but some times mfr's disable cruise when brake light(s)is out. Otherwise try fuse.
To troubleshoot the cruise control on a 1998 Ford F-150, first check the fuse related to the cruise control system in the fuse box. Next, inspect the brake pedal switch, as a faulty switch can disable cruise control when the brakes are pressed. Additionally, examine the throttle cable for any signs of wear or binding, and ensure that the cruise control module connections are secure. If the issue persists, consider using a diagnostic scanner to check for any error codes related to the system.
To fix the cruise control on a 1998 Volvo S70, first check the fuse associated with the cruise control system, as a blown fuse can prevent it from functioning. Inspect the brake switch, as a malfunction here can disable the cruise control when the brake is applied. Additionally, examine the throttle cable for any damage or disconnection, and ensure the cruise control module is receiving power. If these components are in good condition but the issue persists, consider consulting a professional for further diagnostics.
Your speed sensor probably broke and needs to be replaced. If the car can't determine it's speed, then it may automatically disable the cruise control.
Cruise control is an accessory.
If the cruise control on your Lexus RX 300 has stopped working, it could be due to several issues. Common causes include a blown fuse, a malfunctioning cruise control switch, or problems with the brake pedal sensor, which can disable the system. Checking the vehicle's fuse box for any blown fuses related to the cruise control system is a good first step. If the issue persists, it may be best to consult a mechanic for further diagnosis.
It is possible to convert a car without cruise control to have cruise control. Many auto parts stores sell kits which will install cruise control in a vehicle.
There are several ways to fix the cruise control on your Mercedes-Benz depending on the problem with the cruise control. Make sure the fuse for the cruise control is not blown.
To troubleshoot the cruise control on a 1998 GMC Sonoma, first check the cruise control fuse and replace it if necessary. Next, inspect the brake pedal switch to ensure it’s functioning properly, as a faulty switch can disable the system. Additionally, examine the throttle cable for any signs of wear or blockage, and check the cruise control module for any error codes. If these components are in good condition, consider consulting a professional for further diagnostics.