0
What else can I help you with?
What are the wiring colors for stereo in 98' Firebird?
1996 Ford Thunderbird Car Stereo Radio Wiring DiagramRadio Constant 12V+ Wire: Black/OrangeRadio Ignition Switched 12V+ Wire: Yellow/BlackRadio Ground Wire: Black/Light GreenRadio Illumination Dimmer Wire: Light GreenRadio Antenna Trigger Wire: N/ARadio Amplifier Trigger Wire: Dark BlueFront Speakers Size: 5″ x 7″Front Speakers Location: DoorsLeft Front Speaker Wire (+): Orange/Light GreenLeft Front Speaker Wire (-): Light Blue/WhiteRight Front Speaker Wire (+): White/GreenRight Front Speaker Wire (-): Green/OrangeRear Speakers Size: 5″ x 7″Rear Speakers Location: Side PanelsLeft Rear Speaker Wire (+): Gray/Light BlueLeft Rear Speaker Wire (-): Tan/YellowRight Rear Speaker Wire (+): Orange/RedRight Rear Speaker Wire (-): Brown/Pink
How do you connect daytime running lights for 2004 Honda Element?
First you must be able to use a test light. .. Remove the clam shell that encloses the steering column. Then with the key off and removed find the bundle of wires that go to the light switch. Turn on the head lights and probe the wires one by one till you find one that lights up. STAY AWAY FROM THE YELLOW WIRE BUNDLE THIS IS THE AIR BAG YOU WILL DIE. With the light probe lit turn off the headlights and if the probe goes out you have found the running light wire , try again till the wire goes out as the headlights do. First you must be able to use a test light. .. Remove the clam shell that encloses the steering column. Then with the key off and removed find the bundle of wires that go to the light switch. Turn on the head lights and probe the wires one by one till you find one that lights up. STAY AWAY FROM THE YELLOW WIRE BUNDLE THIS IS THE AIR BAG YOU WILL DIE. With the light probe lit turn off the headlights and if the probe goes out you have found the running light wire , try again till the wire goes out as the headlights do.
Wiring sound and light define the following polarity of the screw colors brass bronze silver green?
Brass (or bronze) is the "hot" wire, (Black, red, or blue) silver is for the neutral (the white wire) and green is for, well, the green or bare wire
Does a ballast use electricity if no bulbs are present?
If you mean the ballast in a fluorescent light fitting where the ballast is wired in series with the tube, the answer is "No". Explanation: If no tube is in place, the light fitting's circuit is "open" so there is nothing to take any current from the "hot" supply wire and return it to the "neutral" wire.
Where can you get access to watch the mini-series called The Corner It is similar to The Wire...?
try youtube thats were i watch with out signing up if its not on hulu or netflix but those you have to sign up
How do you wire a beacon light?
To wire a beacon light, add the proper resistor to the LED. Then bypass the decoder and wire the LED's cathode and anode to the opposite rails.
On a silicon-controlled rectifier which wire is the anode and which the cathode?
Anode is positive, cathode is negative
What is a synonym for electrode?
According to Thesaurus.com synonyms: copper cathode, inert anode, inert cathode,plate, wire, zinc anode
Can you identify the wire I need to cut to disable the check engine light on a 2001 eclipse spyder?
I WOULDNT ADVISE DOING THAT.
How do you wire Bi-color LEDs?
Treat each color as a separate LED and wire accordingly. Be sure to observe the polarity of the component (anode and cathode +/-)
How do you wire Bi color LEDs?
Treat each color as a separate LED and wire accordingly. Be sure to observe the polarity of the component (anode and cathode +/-)
What are the live and neutral wires in a ceiling light?
The live wire is the wire that carries electrical current to the light fixture, while the neutral wire provides a return path for the current to complete the circuit. In a ceiling light, the live wire is typically colored black or red, while the neutral wire is colored white or gray. It is important to properly identify and connect these wires to ensure safe operation of the light fixture.
How do you identify the leads of a diode?
There are two wires on a diode: Anode (positive in) and Cathode (negative out). A diode may have a grey band at the cathode end, and black at the anode end. Diodes come in many sizes and capacities, some with clear markings, some without, so there are times when a multimeter has to be used. Set the multimeter to the diode setting (looks like an horizontal arrow fired from a bow, with three lines meeting at the arrow-head's tip). Touch one wire with the red + probe, and the other wire with the black - probe. If there is no reaction, electricity is not flowing. Reverse the probes and you should get a reaction showing that electricity has been detected. So the red probe marks the anode wire and the black probe marks the cathode wire. If there is no reaction, whichever probes are tried, then the diode is dead.
What is a light wire?
A light wire is probably a wire with light in it, but to be honest, I haven't really heard of it. lol
If you want to add a light in a closet can you tap into a three wire red white black that is running between the two switches powering your hallway light and if so how?
Three wire strand running between 2 switches is for a 3 way switch. It is only one side of the circuit. Since it is only one side and switches between the 3 wires there is no way to use it for a light. There may be power at the hall light, but I have seen all types of wiring and each circumstance has to be looked at on it's own.
What are the ratings and certificates for The Wire - 2002 Corner Boys 4-8?
The Wire - 2002 Corner Boys 4-8 is rated/received certificates of: Netherlands:16
How do I wire a light switch to a light?
To wire a light switch to a light, first turn off the power to the circuit. Connect the black wire from the switch to the black wire from the light. Connect the white wire from the switch to the white wire from the light. Finally, connect the ground wire from the switch to the ground wire from the light. Secure all connections with wire nuts and cover with electrical tape. Turn the power back on and test the switch to ensure it is working properly.
