answersLogoWhite

0

What else can I help you with?

Continue Learning about Movies & Television

How are safety switches wired to the holding coil?

In control circuit wiring the safety switch is in series with the holding coil.


How can you include phase failure relay in your star delta motor starter circuit?

The star delta motor starter circuit has to have a control voltage to energize the motor magnetic contractors. A phase failure relay monitors all three phases of the incoming supply lines. The phase failure relay also has auxiliary contacts on it. There are usually two sets of "C" form contacts. The control voltage for the starter circuit must be connected across the normally open (N.O.) contacts of one of these two sets. When the phase monitor is energized these N.O. contacts close supplying the control voltage to the circuitry of the star delta starters. If there is a phase interruption, phase reversal or phase loss, the phase failure relay will de-energize and the N.O. contacts will go back to their de-energized state. If the star delta motor starter is in use at the time, its control circuitry voltage will be lost and the delta motor magnetic contactor will open. The opening of this contactor will disconnect the motor from the failed three phase supply.


When using a 3 wire control circuit to control a magnetic motor starter the part that will open the control circuit when an overload occurs will be?

The part that opens the circuit is the overload blocks that are situated below the magnetic starter and before the motor load. The latest addition to the electrical code book states that the "hot" wire goes through the overload contacts first before feeding the 3 wire control system. With the supply voltage in this position the whole circuit becomes de-energized when the motor load trips the circuit. The old standard practice on a 3 wire control system, the neutral was connected to the overload relay contacts. When the overload relay tripped it opened the neutral of the coil circuit and the starter dropped out


What is the role of a switch?

A switch is installed in a circuit to stop the current flow. Without the switch there is no way to disconnect the operation of the circuit's load. In modern households the switch is a convenient way to control room lighting from a convenient location. Without switches the circuit power would have to be controlled from the service distribution panel's breakers. In this scenario the breaker would be in the same class as a switch.


What are two uses for variable resistors?

Volume Control Light Dimmer Tone Control Bass Control Treble Control Fan Speed Control

Related Questions

How many wires to control a mechanically held contactor?

A contactor is a type of switch. However this switch uses electricity to power an electromagnetic coil to switch on or off power. Hence a contactor needs 2 wires - A live/hot wire and a neutral wire. Generally these are connected across the A1 and A2 terminals of the contactor.


How does magnetic contactor operate?

explain me about the contactor works with examples. if i want to control a motor with contactor. and how i can use contactor in loops with over load and circuit breakers.


What is meant by main contact and auxiliary contact in magnetic contactor?

The main contact controls the load current to the motor, whereas the auxiliary contact is part of the control circuit -usually connected in parallel with the 'on' pushbutton switch to maintain the control circuit in the energised state, once the on pushbutton has been pressed.


What is the purpose of a timer wired into the compressor contactor control circuit on a refrigeration system?

A defrost control typically.


How do switches control circuit?

They break the connection


How do you wire 4-way switches in a circuit?

To wire 4-way switches in a circuit, you connect the traveler wires from each switch to the corresponding terminals on the switches. The common terminal on one switch is connected to the hot wire, while the common terminal on the other switch is connected to the light fixture. This setup allows you to control the light from multiple locations.


Can a 3 phase contactor be wired for single phase?

Yes, L1 of the single phase supply is terminated under terminal L1 of the three phase contactor. L2 of the single phase supply is terminated under terminal L2 of the three phase contactor. A conductor from output terminal T2 is then taken to input terminal L3. The single phase load is then connected to the contactor's output terminals T1 and T3. This incorporates all three of the overload blocks on the contactor into the control circuit. With the overloads in the control circuit, if an overload occurs the magnetic contactor's holding coil will drop out and take the load off line.


How do electro pneumatic contactors work?

A contactor is an electrically controlled switch (relay) used for switching a power circuit. an electro pneumatic contactor is similar to the above except it uses a pneumatic signal to initiate the switching of the electric power circuit. an electro magnetic contactor is a contactor driven by an electric control signal. It us usually just called a contactor.


Do all double pole switches have an off position?

Yes, double pole switches typically have an off position in which the circuit is disconnected and no power is flowing through the switch. This allows for complete control over the power supply to the connected device or circuit.


How do you connect a 3-way switch in a circuit?

To connect a 3-way switch in a circuit, you need to wire it with two other switches to control a single light fixture from multiple locations. The common terminal of the 3-way switch is connected to the power source, while the travelers are connected to the other two switches. This setup allows you to turn the light on or off from any of the three switches.


How do three-way switches work in a lighting circuit to control a single light fixture from two different locations?

Three-way switches in a lighting circuit use two switches to control a single light fixture from two different locations. The switches are connected in a way that allows either switch to turn the light on or off, regardless of the position of the other switch. This setup creates a convenient way to control the light from multiple points in a room.


What is the function of a double pole contactor in an electrical circuit?

A double pole contactor in an electrical circuit is used to control the flow of electricity to two separate circuits simultaneously. It allows for the isolation and switching of both the live and neutral wires in each circuit, providing a higher level of safety and control in the electrical system.