answersLogoWhite

0

Yea, mine did that. I had to replace it. Hope you've been going through the sync process regularly. You might want to check the charger. If it's not working your palm might be ok, just a dead battery. Also check the pins to make sure they aren't bent. If the charger can't connect you palm will never charge. Other than that, either send it in to get it repaired or get a new one.

User Avatar

Wiki User

19y ago

What else can I help you with?

Continue Learning about Movies & Television

Is their a reset button on the PS3 controller?

Yes there is, if you look behind the controller, right above the sticker is a hole with a screw in it, now if you look a little to the right if the hole, you will see a small hole, the reset button is located in there.


How do you set the clock on a '91 corolla DX?

I have a '91 Corolla DX (which I love). -To reset the hour, you have to push the "H" button. -To reset the minutes, use the "M" button. -If you push the "SET" button, it will reset the time to the nearest hour, according to what the display already shows. If the clock shows between 1:01 and 1:29, pushing the "SET" button will change it to 1:00. If the clock shows between 1:30 and 1:59, the "SET" button will change it to 2:00. - Every time the battery is disconnected, the clock will go back to 1:00 and need to be reset.


How do you make your PS3 not HD?

If you want to reset the PS3 to 480i (reset video to lowest setting) hold power button down for 2 beeps (while PS3 is Off)


Where is the reset button in a 91 Honda Prelude to restart the engine after an accident?

ah its not an xbox bro , no reeset button ,you messed up something in your engine or your computers gone to standby


How do you reset your secret password on your monster high journal?

To reset your secret password on your Monster High journal, locate the reset button or switch, usually found on the back or inside cover of the journal. Press and hold this button for a few seconds until you see a prompt or hear a sound indicating the reset is successful. After resetting, you can set a new password by following the on-screen instructions. Always refer to the user manual for specific instructions for your journal model.

Related Questions

Where would you find the reset button on roblox?

You can find the reset button by pressing Esc then hitting reset this is only on pc I think


How do you reboot a Wii?

You can do a normal reset by pressing the power button on either the Wii or any synchronized remote twice. A hard reset (used when a normal reset won't work) is done by unplugging the power cord (from either the Wii or the wall) and plugging it back in, then turning the power on.


How do you reset your work?

By pressing the reset button I would assume. Need a little more information about what is in need of being reset


Where can i find the reset button on a gateway laptop?

Laptops do not generally have a reset button. However pressing and holding the power button usually forces the system to power off, and then pressing it again would start it back up thereby restarting the system.


How can you determine if a GFCI is bad?

To determine if a GFCI is bad, you can press the "test" and "reset" buttons on the outlet. If pressing the "test" button does not trip the outlet or pressing the "reset" button does not restore power, the GFCI may be faulty and should be replaced.


What does the red button on thermostat do?

The red button on a thermostat is often a reset button. Pressing it will reset the thermostat to its default settings. This can be helpful if the thermostat is not functioning properly or if you need to start over with the programming.


How you reset maintenance light on 2009 pilot?

Try holding in the trip mileage reset button while turning the key to the run position. Continue pressing the button for 10 seconds or so. The light should go off. == The manual for my 2008 Pilot says: - Turn ignition switch to ON (II) - Press select/reset knob until engine oil life is displayed. - Press select/reset knob for about 10 seconds until the display starts blinking. - Press select/reset knob for another 5 seconds, the display will reset.


How do you reset your metro pcs phone?

by pressing the lock button , and the volume down volume button at thr same time .


How to light a pilot: Can you provide step-by-step instructions on how to safely and effectively light a pilot?

Here are step-by-step instructions on how to safely and effectively light a pilot: Locate the pilot light assembly on your appliance. Turn the gas knob to the "off" position and wait for any lingering gas to dissipate. Use a long lighter or match to ignite the pilot light. Hold the flame near the pilot burner while pressing the reset button. Once the pilot light is lit, continue holding the reset button for about 30 seconds to allow the thermocouple to heat up. Release the reset button and check to ensure the pilot light remains lit. If it goes out, repeat the process. Turn the gas knob to the "on" position and adjust the flame to the desired level. Remember to always follow the manufacturer's instructions and exercise caution when working with gas appliances.


How can you determine if a GFCI outlet is bad?

To determine if a GFCI outlet is bad, you can press the "test" and "reset" buttons on the outlet. If pressing the "test" button does not trip the outlet or pressing the "reset" button does not restore power, the GFCI outlet may be faulty and should be replaced.


How do you determine if a GFCI outlet is bad?

To determine if a GFCI outlet is bad, you can press the "Test" and "Reset" buttons on the outlet. If pressing the "Test" button does not trip the outlet or pressing the "Reset" button does not restore power, the GFCI outlet may be faulty and should be replaced.


How can I relight the pilot light on my Payne furnace?

To relight the pilot light on your Payne furnace, locate the pilot light assembly and follow the manufacturer's instructions for relighting it. This typically involves turning the gas valve to the pilot position, pressing and holding the reset button, and using a long lighter to ignite the pilot flame. Make sure to follow all safety precautions and guidelines provided in the furnace manual.