0
What is a composite signal and what can obtained from it as components?
Wiki User
∙ 13y ago
That depend on what the signal is a composite of and how these components were combined. Please clarify question.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
What are the component of electronics?
Electronic have two type of components Active components and Passive components. Active components are those which increase the power of a signal and must be supplied with the signal and a source of power. Passive components do not increase the power of a signal. Active components are Bipolar transistor, Operational amplifier, field effect transistors etc and Passive components are semiconductor, resistor, capacitor, inductor etc
Advantages of frequency domain over time domain?
advantage is that if we represent a composite signal in frequency domain........then we clearly see that how much signals are involved in composite signal and their separate peak values
What does lead mean in electronics?
A lead or lag applies to a signal due to active components to make it lead or lag the original signal
How can a composite signal be decomposed into its individual frequencies?
Fourier analysis Frequency-domain graphs
Am demodulator diode detector circuit?
demodulator circuit is a circuit which is used for remove all high frequency components from modulated signal.
What is the definition of a composite signal?
A composite signal is a mux or a bus signal. These can be thought of as a collection of other component signals.
What is a composite attribute?
A composite attribute has multiple components, each of which is atomic or composite.
If the signal going in is Composite, then yes this should work fine.?
If the signal going in is Composite, then yes this should work fine.
What is a composite building?
One made of several components
What are the component of electronics?
Electronic have two type of components Active components and Passive components. Active components are those which increase the power of a signal and must be supplied with the signal and a source of power. Passive components do not increase the power of a signal. Active components are Bipolar transistor, Operational amplifier, field effect transistors etc and Passive components are semiconductor, resistor, capacitor, inductor etc
What is s-video?
S-video is a signal format. It is a development used on domestic video systems to improve the quality of images over the composite video format that was the standard interface between equipment. Composite video uses a single wire to carry both the brightness information (Also known as "luma" or "y") and the colour information (known as "chroma" or "c"). Because of the way the colour is encoded in the signal, there is a limit to the resolution of the signal and some vertical lines can appear smeared or softened because of it. S-video uses two wires to carry the signal. One is just for the luma signal or "y". the other is for the chroma content, or "c". S-video is also known as a yc signal because of the two components. Although the colour information is identical to that of the composite signal, the luma signal is a higher bandwidth that composite. The result is that edges look sharper and the image is a slightly higher resolution.
How does bispectral analysis use data obtained by electroencephalogram?
Bispectral analysis is a method of analyzing the mathematical relationships among the various components of an EEG signal (phase couplings) as well as measuring amplitudes and frequencies.
What the difference between the single carrier and the multi-carrier modulation?
Multi-carrier modulation (MCM) is a method of transmitting data by splitting it into several components, and sending each of these components over separate carrier signals. The individual carriers have narrow bandwidth , but the composite signal can have broad bandwidth.
What defines the bandwith of a composite signal?
The width of the frequency spectrum
What are composite signals why you needed?
In case of TV broad casting, the Video Signal is not transmitted alone, but it accompanied by a number of other signals or pulses, which help the exact reproduction of the picture at the receiving end. These pulses include Blanking Pulses, Synchronizing pulses and Equalizing pulses. A combination of Picture signal and other Controlling signal or pulses is called Composite Signal. Thus Composite Video Signal may consist of Following Parts.Picture information (Data)Blanking Pulses (Delay Pulses)Vertical and Horizontal Synchronizing Pulses (controlling Pulses)Generally,A Combination of Data and Other Controlling Signal is Called Composite Signal .
Advantages of frequency domain over time domain?
advantage is that if we represent a composite signal in frequency domain........then we clearly see that how much signals are involved in composite signal and their separate peak values
What is convolution of a signal?
the convolution of a signal is to filter the components of the signal. The convolution does not mean the masking. Masking means it is going to remove all the masked components(both high and low frequency components).But convolution is going to remove any one (either low r high frequency) depending upon the filter response.
