0
to step up or step down high voltage
AnswerThe principle is that of electromagnetism.An auto transformer has only one winding which has (usually) one tap on it.
If a voltage is applied across the whole winding, and connections are made between one end and the tap, a lower voltage is available on those connections.
The magnitude of that voltage has a ratio to the overall applied voltage as the ratio of the number of turns across which the voltage is taken, to the total number of turns.
Or, if a voltage is applied between one end of the winding and the tap, then an increased voltage may be obtained across the whole winding.
The ratio of the two voltages being the same as the ratio between the number ..... but I'm sure you can guess the rest.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
Advantages of autotransformer?
the power can flow either way through autotransformer (345/120 kV) ?
What is the working principle of autotransformer?
An autotransformer is no different than a regular transformer. It has "effectively" two windings, a primary and a secondary. Its just that one end of the primary is connected to one end of the secondary. It can also be said that it has only one winding, and that there is a tap someplace in that winding, but the end result is the same. Depending on how it is connected, it can step up or step down the voltage. Some autotransformers have multiple taps. Some, called variacs, have a sliding contact that allows relatively fine control of the output. The up side of an autotransformer is that it can be easier to build. The downside is that it does not provide electrical isolation between primary and secondary, nor can it filter harmonics as well as a dual winding transformer.
What is the Working principle of auto transformer?
An autotransformer (sometimes called autoformer)[1] is an electrical transformer with only one winding. The winding has at least three electrical connection points called taps. The voltage source and the load are each connected to two taps. One tap at the end of the winding is a common connection to both circuits (source and load). Each tap corresponds to a different source or load voltage. In an autotransformer a portion of the same winding acts as part of both the primary and secondary winding. Operation he ratio of secondary to primary voltages is equal to the ratio of the number of turns of the winding they connect to. For example, connecting at the middle and bottom of the autotransformer will halve the voltage. Depending on the application, that portion of the winding used solely in the higher-voltage (lower current) portion may be wound with wire of a smaller gauge, though the entire winding is directly connected.
When was The Lucifer Principle created?
The Lucifer Principle was created in 1995-01.
What is principle of communication system?
The principle of passing information from one place to another.
What is an autotransformer?
An autotransformer is a transformer where the primary and secondary are a single winding.
Advantages of autotransformer?
the power can flow either way through autotransformer (345/120 kV) ?
What is the principle of operation of a ballast?
Older ballasts with an iron core are basically an autotransformer. They transform voltage to a higher voltage with a single winding. Electronic transformers increase voltage with capacitors and diodes.
Vector group of autotransformer?
YNyn0
Who invented autotransformer?
Talha Idrees
What does cwa stand for?
Constant Wattage Autotransformer
What is the another name of autotransformer?
autostep down transformer
What is single phase autotransformer?
An autotransformer is a transformer with at least two windings where a part of one winding (the common winding) is shared between both primary and secondary outputs.
Why you not use auto transformer for distribution purpose?
because autotransformer used for both purpose step up and step down but dustrubution need step down in case of this autotransformer not used for dustrubtion purpouseAnswerBecause an autotransformer (not 'auto transformer') does not provide electrical isolation between the secondary and primary.
Which are the different types of winding connection in autotransformer?
fixed taps and variable resistance
What are disadvantages autotransformer?
cannot be used as an isolating transformer, because is has common winding.
What is the working principle of autotransformer?
An autotransformer is no different than a regular transformer. It has "effectively" two windings, a primary and a secondary. Its just that one end of the primary is connected to one end of the secondary. It can also be said that it has only one winding, and that there is a tap someplace in that winding, but the end result is the same. Depending on how it is connected, it can step up or step down the voltage. Some autotransformers have multiple taps. Some, called variacs, have a sliding contact that allows relatively fine control of the output. The up side of an autotransformer is that it can be easier to build. The downside is that it does not provide electrical isolation between primary and secondary, nor can it filter harmonics as well as a dual winding transformer.
