50% of the input signal is used (Θ = 180° or π; i.e., the active element works in its linear range half of the time and is more or less turned off for the other half). In most Class B, there are two output devices (or sets of output devices), each of which conducts alternately (push-pull) for exactly 180° (or half cycle) of the input signal; selective RF amplifiers can also be implemented using a single active element.
These amplifiers are subject to crossover distortion if the transition from one active element to the other is not perfect, as when two complementary transistors (i.e., one PNP, one NPN) are connected as two emitter followers with their base and emitter terminals in common, requiring the base voltage to slew across the region where both devices are turned off.Class ABHere the two active elements conduct more than half of the time as a means to reduce the cross-over distortions of Class B amplifiers. In the example of the complementary emitter followers a bias network allows for more or less quiescent current thus providing an operating point somewhere between Class A and Class B. Sometimes a figure is added (e.g., AB1 or AB2) for vacuum tube stages where the grid voltage is always negative with respect to the cathode (Class AB1) or may be slightly positive (hence drawing grid current, adding more distortion, but giving slightly higher output power) on signal peaks (Class AB2); another interpretation being higher figures implying a higher quiescent current and therefore more of the properties of Class A.Class CLess than 50% of the input signal is used (conduction angle Θ < 180°). The advantage is potentially high efficiency, but a disadvantage is high distortion.Class D
Main article: Switching amplifier These use switching to achieve a very high power efficiency (more than 90% in modern designs). By allowing each output device to be either fully on or off, losses are minimized. The analog output is created by pulse-width modulation; i.e., the active element is switched on for shorter or longer intervals instead of modifying its resistance. There are more complicated switching schemes like sigma-delta modulation, to improve some performance aspects like lower distortions or better efficiency.Additional classesThere are several other amplifier classes, although they are mainly variations of the previous classes. For example, Class G and Class H amplifiers are marked by variation of the supply rails (in discrete steps or in a continuous fashion, respectively) following the input signal. Wasted heat on the output devices can be reduced as excess voltage is kept to a minimum. The amplifier that is fed with these rails itself can be of any class. These kinds of amplifiers are more complex, and are mainly used for specialized applications, such as very high-power units. Also, Class E and Class F amplifiers are commonly described in literature for radio frequencies applications where efficiency of the traditional classes in are important, yet several aspects not covered elsewhere (e.g.: amplifiers often simply said to have a gain of x dB - so what power gain?) deviate substantially from their ideal values. These classes use harmonic tuning of their output networks to achieve higher efficiency and can be considered a subset of Class C due to their conduction angle characteristics.
The classes can be most easily understood using the diagrams in each section below. For the sake of illustration, a bipolar junction transistor is shown as the amplifying device, but in practice this could be a MOSFET or vacuum tube device. In an analog amplifier (the most common kind), the signal is applied to the input terminal of the device (base, gate or grid), and this causes a proportional output drive current to flow out of the output terminal. The output drive current comes from the power supply.
Class AClass A amplifier
Amplifying devices operating in Class A conduct over the whole of the input cycle such that the output signal is an exact scaled-up replica of the input with no clipping. A Class A amplifier (or operational amplifier) is distinguished by the output stage (and perhaps the driver) device(s) being biased into Class A; even Class AB and B amplifiers normally have early stages operating in Class A. Class A is the usual means of implementing small-signal amplifiers, so the term Class A design applied to equipment such as preamplifiers (for example, in recording studios) implies not so much their use of Class A, but that their sound is top quality - good enough to be matched with top quality Class A power amplifiers.
Advantages of Class A AmplifiersClass A designs have largely been superseded by the more efficient designs for power amplifiers, though they remain popular with some hobbyists, mostly for their simplicity. Also, many audiophiles believe that Class A gives the best sound quality (for their absence of crossover distortion and reduced odd-harmonic and high-order harmonic distortion) which provides a small market for expensive high fidelity Class A amps.
Single-Ended and Triode Class A AmplifiersSome aficionados who prefer Class A amplifiers also prefer the use of thermionic valve (or "tube") designs instead of transistors, especially in Single-ended triode output configurations for several claimed reasons:
Transistors are much cheaper, and so more elaborate designs that give greater efficiency but use more parts are still cost-effective. A classic application for a pair of class A devices is the long-tailed pair, which is exceptionally linear, and forms the basis of many more complex circuits, including many audio amplifiers and almost all op-amps. Class A amplifiers are often used in output stages of high quality op-amps (although the accuracy of the bias in low cost op-amps such as the 741 may result in Class A or Class AB or Class B, varying from device to device or with temperature). They are sometimes used as medium-power, low-efficiency, and high-cost audio amplifiers. The power consumption is unrelated to the output power. At idle (no input), the power consumption is essentially the same as at high output volume. The result is low efficiency and high heat dissipation.
Class B and ABClass B amplifiers only amplify half of the input wave cycle, thus creating a large amount of distortion, but their efficiency is greatly improved and is much better than Class A. Class B has a maximum theoretical efficiency of 78.5% (i.e., π/4). This is because the amplifying element is switched off altogether half of the time, and so cannot dissipate power. A single Class B element is rarely found in practice, though it has been used for driving the loudspeaker in the early IBM Personal Computers with beeps, and it can be used in RF power amplifier where the distortion levels are less important. However Class C is more commonly used for this.Class B Amplifier
A practical circuit using Class B elements is the push-pull stage, such as the very simplified complementary pair arrangement shown below. Here, complementary or quasi-complementary devices are each used for amplifying the opposite halves of the input signal, which is then recombined at the output. This arrangement gives excellent efficiency, but can suffer from the drawback that there is a small mismatch in the cross-over region - at the "joins" between the two halves of the signal, as one output device has to take over supplying power exactly as the other finishes. This is called crossover distortion. An improvement is to bias the devices so they are not completely off when they're not in use. This approach is called Class AB operation.
In Class AB operation, each device operates the same way as in Class B over half the waveform, but also conducts a small amount on the other half. As a result, the region where both devices simultaneously are nearly off (the "dead zone") is reduced. The result is that when the waveforms from the two devices are combined, the crossover is greatly minimised or eliminated altogether. The exact choice of quiescent current, the standing current through both devices when there is no signal, makes a large difference to the level of distortion (and to the risk of thermal runaway, that may damage the devices); often the bias voltage applied to set this quiescent current has to be adjusted with the temperature of the output transistors (for example in the circuit at the beginning of the article the diodes would be mounted physically close to the output transistors, and chosen to have a matched temperature coefficient). Another approach (often used as well as thermally-tracking bias voltages) is to include small value resistors in series with the emitters.
Class AB sacrifices some efficiency over class B in favor of linearity, thus is less efficient (below 78.5% for full-amplitude sinewaves in transistor amplifiers, typically; much less is common in Class AB vacuum tube amplifiers). It is typically much more efficient than class A.
Class B push-pull amplifier
Class B or AB push-pull circuits are the most common design type found in audio power amplifiers. Class AB is widely considered a good compromise for audio amplifiers, since much of the time the music is quiet enough that the signal stays in the "class A" region, where it is amplified with good fidelity, and by definition if passing out of this region, is large enough that the distortion products typical of class B are relatively small. The crossover distortion can be reduced further by using negative feedback. Class B and AB amplifiers are sometimes used for RF linear amplifiers as well. Class B amplifiers are also favored in battery-operated devices, such as transistor radios.
Digital Class BA limited power output Class-B amplifier with a single-ended supply rail of 5±0.5 V.
Class CClass C amplifier
Class C amplifiers conduct less than 50% of the input signal and the distortion at the output is high, but high efficiencies (up to 90%) are possible. Some applications (for example, megaphones) can tolerate the distortion. A much more common application for Class C amplifiers is in RF transmitters, where the distortion can be vastly reduced by using tuned loads on the amplifier stage. The input signal is used to roughly switch the amplifying device on and off, which causes pulses of current to flow through a tuned circuit.
The Class C amplifier has two modes of operation: tuned and untuned.[10] The diagram shows a waveform from a simple class C circuit without the tuned load. This is called untuned operation, and the analysis of the waveforms shows the massive distortion that appears in the signal. When the proper load (e.g., a pure inductive-capacitive filter) is used, two things happen. The first is that the output's bias level is clamped, so that the output variation is centered at one-half of the supply voltage. This is why tuned operation is sometimes called a clamper. This action of elevating bias level allows the waveform to be restored to its proper shape, allowing a complete waveform to be re-established despite having only a one-polarity supply. This is directly related to the second phenomenon: the waveform on the center frequency becomes much less distorted. The distortion that is present is dependent upon the bandwidth of the tuned load, with the center frequency seeing very little distortion, but greater attenuation the farther from the tuned frequency that the signal gets.
The tuned circuit will only resonate at particular frequencies, and so the unwanted frequencies are dramatically suppressed, and the wanted full signal (sine wave) will be extracted by the tuned load (e.g., a high-quality bell will ring at a particular frequency when it is hit periodically with a hammer). Provided the transmitter is not required to operate over a very wide band of frequencies, this arrangement works extremely well. Other residual harmonics can be removed using a filter.
Class DMain article: Class D Amplifier
Block diagram of a basic switching or PWM (Class-D) amplifier.
Boss Audio Class D mono car audio amplifier with a low pass filter for powering subwoofers
In the Class D amplifier the input signal is converted to a sequence of higher voltage output pulses. The averaged-over-time power values of these pulses are directly proportional to the instantaneous amplitude of the input signal. The frequency of the output pulses is typically ten or more times the highest frequency in the input signal to be amplified. The output pulses contain inaccurate spectral components (that is, the pulse frequency and its harmonics) which must be removed by a low-pass passive filter. The resulting filtered signal is then an amplified replica of the input.
These amplifiers use pulse width modulation, pulse density modulation (sometimes referred to as pulse frequency modulation) or more advanced form of modulation such as Delta-sigma modulation (for example, in the Analog Devices AD1990 Class-D audio power amplifier). Output stages such as those used in pulse generators are examples of Class D amplifiers. The term Class D is usually applied to devices intended to reproduce signals with a bandwidth well below the switching frequency.
Class D amplifiers can be controlled by either analog or digital circuits. The digital control introduces additional distortion called quantization error caused by its conversion of the input signal to a digital value.
The main advantage of a Class D amplifier is power efficiency. Because the output pulses have a fixed amplitude, the switching elements (usually MOSFETs, but valves and bipolar transistors were once used) are switched either completely on or completely off, rather than operated in linear mode. A MOSFET operates with the lowest resistance when fully-on and thus has the lowest power dissipation when in that condition, except when fully off. When operated in a linear mode the MOSFET has variable amounts of resistance that vary linearly with the input voltage and the resistance is something other than the minimum possible, therefore more electrical energy is dissipated as heat. Compared to Class A/B operation, Class D's lower losses permit the use of a smaller heat sink for the MOSFETS while also reducing the amount of AC power supply power required. Thus, Class D amplifiers do not need as large or as heavy power supply Transformers or heatsinks, so they are smaller and more compact in size than an equivalent Class AB amplifier.
Class D amplifiers have been widely used to control motors, and almost exclusively for small DC motors, but they are now also used as audio amplifiers, with some extra circuitry to allow analogue to be converted to a much higher frequency pulse width modulated signal. The relative difficulty of achieving good audio quality means that nearly all are used in applications where quality is not a factor, such as modestly-priced bookshelf audio systems and "DVD-receivers" in mid-price Home Theater systems.
High quality Class D audio amplifiers are now, however, starting to appear in the market:
These revised designs have been said to rival good traditional AB amplifiers in terms of quality.
Before these higher quality designs existed an earlier use of Class D amplifiers and prolific area of application was high-powered, subwoofer amplifiers in cars. Because subwoofers are generally limited to a bandwidth of no higher than 150 Hz, the switching speed for the amplifier does not have to be as high as for a full range amplifier. The drawback with Class D designs being used to power subwoofers is that their output filters (typically inductors that convert the pulse width signal back into an analogue waveform) lower the damping factor of the amplifier.
This means that the amplifier cannot prevent the subwoofer's reactive nature from lessening the impact of low bass sounds (as explained in the feedback part of the Class AB section). Class D amplifiers for driving subwoofers are relatively inexpensive, in comparison to Class AB amplifiers. A 1000 W Class D subwoofer amplifier that can operate at about 80% to 95% efficiency costs about US$250, much less than a Class AB amplifier of this power, which would cost several thousand dollars.
The letter D used to designate this amplifier class is simply the next letter after C, and does not stand for digital. Class D and Class E amplifiers are sometimes mistakenly described as "digital" because the output waveform superficially resembles a pulse-train of digital symbols, but a Class D amplifier merely converts an input waveform into a continuously pulse-width modulated (square wave) analog signal. (A digital waveform would be pulse-code modulated.)
Additional classesClass EThe Class E/F amplifier is a highly efficient switching power amplifier, typically used at such high frequencies that the switching time becomes comparable to the duty time. As said in the Class D amplifier, the transistor is connected via a serial LC circuit to the load, and connected via a large L (inductor) to the supply voltage. The supply voltage is connected to ground via a large capacitor to prevent any RF signals leaking into the supply. The Class E amplifier adds a C (capacitor) between the transistor and ground and uses a defined L1 to connect to the supply voltage.
Class E Amplifier
The following description ignores DC, which can be added easily afterwards. The above mentioned C and L are in effect a parallel LC circuit to ground. When the transistor is on, it pushes through the serial LC circuit into the load and some current begins to flow to the parallel LC circuit to ground. Then the serial LC circuit swings back and compensates the current into the parallel LC circuit. At this point the current through the transistor is zero and it is switched off. Both LC circuits are now filled with energy in C and L0. The whole circuit performs a damped oscillation. The damping by the load has been adjusted so that some time later the energy from the Ls is gone into the load, but the energy in both C0 peaks at the original value to in turn restore the original voltage so that the voltage across the transistor is zero again and it can be switched on.
With load, frequency, and duty cycle (0.5) as given parameters and the constraint that the voltage is not only restored, but peaks at the original voltage, the four parameters (L, L0, C and C0) are determined. The Class E amplifier takes the finite on resistance into account and tries to make the current touch the bottom at zero. This means that the voltage and the current at the transistor are symmetric with respect to time. The Fourier transform allows an elegant formulation to generate the complicated LC networks and says that the first harmonic is passed into the load, all even harmonics are shorted and all higher odd harmonics are open.
Class E uses a significant amount of second-harmonic voltage. The second harmonic can be used to reduce the overlap with edges with finite sharpness. For this to work, energy on the second harmonic has to flow from the load into the transistor, and no source for this is visible in the circuit diagram. In reality, the impedance is mostly reactive and the only reason for it is that Class E is a Class F (see below) amplifier with a much simplified load network and thus has to deal with imperfections.
In many amateur simulations of Class E amplifiers, sharp current edges are assumed nullifying the very motivation for Class E and measurements near the transit frequency of the transistors show very symmetric curves, which look much similar to Class F simulations.
The Class E amplifier was invented in 1972 by Nathan O. Sokal and Alan D. Sokal, and details were first published in 1975.[11] Some earlier reports on this operating class have been published in Russian.
Class FIn push-pull amplifiers and in CMOS, the even harmonics of both transistors just cancel. Experiment shows that a square wave can be generated by those amplifiers and theory shows that square waves do consist of odd harmonics only. In a Class D amplifier, the output filter blocks all harmonics; i.e., the harmonics see an open load. So even small currents in the harmonics suffice to generate a voltage square wave. The current is in phase with the voltage applied to the filter, but the voltage across the transistors is out of phase. Therefore, there is a minimal overlap between current through the transistors and voltage across the transistors. The sharper the edges, the lower the overlap.
While Class D sees the transistors and the load as two separate modules, Class F admits imperfections like the parasitics of the transistor and tries to optimise the global system to have a high impedance at the harmonics. Of course there has to be a finite voltage across the transistor to push the current across the on-state resistance. Because the combined current through both transistors is mostly in the first harmonic, it looks like a sine. That means that in the middle of the square the maximum of current has to flow, so it may make sense to have a dip in the square or in other words to allow some overswing of the voltage square wave. A Class F load network by definition has to transmit below a cutoff frequency and reflect above.
Any frequency lying below the cutoff and having its second harmonic above the cutoff can be amplified, that is an octave bandwidth. On the other hand, an inductive-capacitive series circuit with a large inductance and a tunable capacitance may be simpler to implement. By reducing the duty cycle below 0.5, the output amplitude can be modulated. The voltage square waveform will degrade, but any overheating is compensated by the lower overall power flowing. Any load mismatch behind the filter can only act on the first harmonic current waveform, clearly only a purely resistive load makes sense, then the lower the resistance, the higher the current.
Class F can be driven by sine or by a square wave, for a sine the input can be tuned by an inductor to increase gain. If Class F is implemented with a single transistor, the filter is complicated to short the even harmonics. All previous designs use sharp edges to minimise the overlap.
Classes G and HThere are a variety of amplifier designs that enhance Class AB output stages with more efficient techniques to achieve greater efficiencies with low distortion. These designs are common in large audio amplifiers since the heatsinks and power transformers would be prohibitively large (and costly) without the efficiency increases. The terms "Class G" and "Class H" are used interchangeably to refer to different designs, varying in definition from one manufacturer or paper to another.
Class G amplifiers (which use "rail switching" to decrease power consumption and increase efficiency) are more efficient than Class AB amplifiers. These amplifiers provide several power rails at different voltages and switch between them as the signal output approaches each level. Thus, the amplifier increases efficiency by reducing the wasted power at the output transistors. Class G amplifiers are more efficient than Class AB but less efficient when compared to Class D, without the negative EMI effects of Class D.
Class H amplifiers take the idea of Class G one step further creating an infinitely variable supply rail. This is done by modulating the supply rails so that the rails are only a few volts larger than the output signal at any given time. The output stage operates at its maximum efficiency all the time. Switched-mode power supplies can be used to create the tracking rails. Significant efficiency gains can be achieved but with the drawback of more complicated supply design and reduced THD performance.
The voltage signal shown is thus a larger version of the input, but has been changed in sign (inverted) by the amplification. Other arrangements of amplifying device are possible, but that given (that is, common emitter, common source or common cathode) is the easiest to understand and employ in practice. If the amplifying element is linear, then the output will be faithful copy of the input, only larger and inverted. In practice, transistors are not linear, and the output will only approximate the input. Non-linearity from any of several sources is the origin of distortion within an amplifier. Which class of amplifier (A, B, AB or C) depends on how the amplifying device is biased - in the diagrams the bias circuits are omitted for clarity.
Any real amplifier is an imperfect realization of an ideal amplifier. One important limitation of a real amplifier is that the output it can generate is ultimately limited by the power available from the power supply. An amplifier will saturate and clip the output if the input signal becomes too large for the amplifier to reproduce or if operational limits for a device are exceeded.
For additional information on Class H: Efficiency Class H
Like many electronic devices, tubes (aka valves) are closer to linear in certain operating ranges--meaning the output is a scaled version of the input when operating in the linear region. However, these linear regions are not typically at zero volts. So a DC bias is added to the AC input signal, shifting the signal into the linear region of the device. The DC bias can be removed from the output, leaving the amplified signal. Essentially the bias shifts the "zero" point for the signal to match the amplifier characteristics. Choosing bias is an important consideration in amplifier design. Amplifiers are designated by a "class" according to their bias--class A, class B, class AB, class C (there are other classes but they aren't used with tubes). Because the bias signal is the zero signal input, the bias determines how much power the tube uses when idle. For example, a class A amplifier is biased to the middle of the tube operating range so it uses about 50% power when idle, which is wasteful and makes a lot of heat.
So as to deliver a fair and impartial trial. Bias would militate against delivering impartiality.
38
A depletion mode MOSFET is a FET that is on with no gate bias, and requires a negative bias (with respect to the source) to stop conducting. The channel is normally conductive and with a negative gate bias the channel becomes "depleted" of charge carriers, hence the name depletion mode MOSFET. This is contrary to enhancement type MOSFET's that are non conductive with zero volts gate bias and become conductive when there is a positive bias on their gate.
There are few who would argue the bias of the media is liberal. Overwhelmingly.
Like many electronic devices, tubes (aka valves) are closer to linear in certain operating ranges--meaning the output is a scaled version of the input when operating in the linear region. However, these linear regions are not typically at zero volts. So a DC bias is added to the AC input signal, shifting the signal into the linear region of the device. The DC bias can be removed from the output, leaving the amplified signal. Essentially the bias shifts the "zero" point for the signal to match the amplifier characteristics. Choosing bias is an important consideration in amplifier design. Amplifiers are designated by a "class" according to their bias--class A, class B, class AB, class C (there are other classes but they aren't used with tubes). Because the bias signal is the zero signal input, the bias determines how much power the tube uses when idle. For example, a class A amplifier is biased to the middle of the tube operating range so it uses about 50% power when idle, which is wasteful and makes a lot of heat.
the decision about what to include and exclude.
bias
So you can keep an eye out for potential bias.
an important measure for controlling bias. -apex (;
So as to deliver a fair and impartial trial. Bias would militate against delivering impartiality.
It helps historians to remember to check other sources for facts.
The term for this is bias. Bias can influence how information is presented, leading to a skewed or unfair portrayal of a topic. It is important to be aware of bias in order to critically evaluate sources of information.
TRUE
TRUE
You can't have bias because of your hypothesis. It's important to have an open mind.
Make your students raise their hands and vote while they have their eyes shut.