0
In theory it can but requires infinite bandwidth. A square wave (or pulse) is a combination of the fundamental frequency and the odd harmonics. If you send a square wave of 1kHz, you need to also be able to send 3kHz, 5kHz, 7kHz, 11kHz ....... etc. Since the bandwidth allowed for most SSB transmissions only allow up to 3kHz bandwidth, all you get is the fundamental of a 1kHz sin wave. On the other hand, if you send a 200Hz tone you can send 200Hz, 600Hz, 1kHz, 1.4Hz, 1.8Hz, 2.2kHz 2.6kHz and this combination will look a lot more like the original 200Hz square wave tone.
What else can I help you with?
Amplitude modulation compared to Pulse position modulation'?
Amplitude modulation (AM) is a technique used in electronic communication, most commonly for transmitting information via a radio carrier wave. AM works by varying the strength of the transmitted signal in relation to the information being sent. For example, changes in the signal strength can be used to reflect the sounds to be reproduced by a speaker, or to specify the light intensity of television pixels. (Contrast this with frequency modulation, also commonly used for sound transmissions, in which the frequency is varied; and phase modulation, often used in remote controls, in which the phase is varied) In the mid-1870s, a form of amplitude modulation-initially called "undulatory currents"-was the first method to successfully produce quality audio over telephone lines. Beginning with Reginald Fessenden's audio demonstrations in 1906, it was also the original method used for audio radio transmissions, and remains in use today by many forms of communication-"AM" is often used to refer to the mediumwave broadcast band (see AM radio). Pulse-position modulation (PPM) is a form of signal modulation in which M message bits are encoded by transmitting a single pulse in one of 2M possible time-shifts. This is repeated every T seconds, such that the transmitted bit rate is M/T bits per second. It is primarily useful for optical communications systems, where there tends to be little or no multipath interference.
In which or what application is a transducer used?
A transducer is used in measuring the levels of fluids in an open or contained environment. It is a secondary piece of equipment that is used along with the equipment to generate and receive the ultra sonic wave pulse. A voltage pulse is sent to the transducer and the time it takes to receive the reflected return of the pulse is calculated by the receiver and converted into a level that is shown on the screen of the receiver. This is one use of a transducer.
What is virtual height of antenna?
Since the ionosphere have different types of layers namely D,E and F layers. So when a pulse transmitted from transmitter it get deflected or we can say reflect by these different layers and reaches to the receiver.Thus the path followed by the pulse is the Actual path.The distance between the highest point of actual path and the earth surface is called Actual height.When a short pulse of energy sent vertically upward and traveling with the speed of light would reach taking the same two rays travel time as does the actual pulse reflected from the ionospheric layers. that height is known as Virtual height of an antenna.
Can you go to jail for getting a minor pregnant in Mississippi if parents don't press charges?
The parents cannot give you permission to break the law. Yes, you can be prosecuted and sent to jail.
What is a SSBSC signal?
Single Side Band Suppressed Carrier. This is a modification of AM (Amplitude Modulation) that both reduces required transmitter power and signal bandwidth. The carrier is first modulated by the signal the same as in ordinary AM, then is sent through a bandpass filter to remove one sideband and the carrier. To demodulate it and recover the original signal the receiver must reinsert the carrier using a BFO (Beat Frequency Oscillator) and Mixer.
What is the advantage of ppm over pwm and Pam?
PPM is a type of pulse modulation where messages are sent using single pulses. PWM is a type of modulation which conforms to the pulse. PAM is a type of modulation in which the information is encoded into a series of pulses.
Why the name pulse code modulation?
because the data is sent as a series of digitally coded numeric values.
What bit rate are peugoet immobilizer codes sent at?
i need to know what baud rate or pulse width modulation duration immobilizer codes are sent at
Amplitude modulation compared to Pulse position modulation'?
Amplitude modulation (AM) is a technique used in electronic communication, most commonly for transmitting information via a radio carrier wave. AM works by varying the strength of the transmitted signal in relation to the information being sent. For example, changes in the signal strength can be used to reflect the sounds to be reproduced by a speaker, or to specify the light intensity of television pixels. (Contrast this with frequency modulation, also commonly used for sound transmissions, in which the frequency is varied; and phase modulation, often used in remote controls, in which the phase is varied) In the mid-1870s, a form of amplitude modulation-initially called "undulatory currents"-was the first method to successfully produce quality audio over telephone lines. Beginning with Reginald Fessenden's audio demonstrations in 1906, it was also the original method used for audio radio transmissions, and remains in use today by many forms of communication-"AM" is often used to refer to the mediumwave broadcast band (see AM radio). Pulse-position modulation (PPM) is a form of signal modulation in which M message bits are encoded by transmitting a single pulse in one of 2M possible time-shifts. This is repeated every T seconds, such that the transmitted bit rate is M/T bits per second. It is primarily useful for optical communications systems, where there tends to be little or no multipath interference.
What are the charateristics of amplitude modulation?
Amplitude modulation (AM) is a method of impressing data onto an alternating current waveform by varying its amplitude in relation to the data being sent. The main characteristics of AM include the modulation index, which determines the amount of variation in the carrier wave, and the sidebands that are created as a result of modulation. AM is susceptible to noise and interference due to its reliance on the amplitude of the signal.
How do you cancel mail you sent on MySpace?
You cannot. Once mail is sent it is sent.
What is function of amplitude modulation?
Amplitude modulation (AM) is a method used in telecommunications to vary the strength (amplitude) of a carrier signal in proportion to the waveform being sent. This modulation technique allows the transmission of audio or data signals through changes in the amplitude of the carrier signal. AM is commonly used in broadcast radio to carry audio signals.
What is revertive pulse dialing?
Revertive pulse dialing is a system first introduced in Panel Switch Exchanges and used only between exchanges in which the called exchange sent back (revertive) dial pulses for each digit to the sending exchange until the sending exchange signaled that the correct number of pulses had been sent for that digit.This is in contrast to standard pulse dialing in which a phone sent dial pulses to the local exchange for each digit or the sending exchange sent dial pulses to the called exchange for each digit.Revertive pulse dialing was considered a more reliable means of transferring numbers between exchanges than standard pulse dialing as certain types of errors in the transfer could be detected that was not possible to detect with standard pulse dialling.A telephone cannot use revertive pulse dialing! It can only be used between exchanges.
Would the crankshaft sensor stop it from starting?
yes aas no pulse signal would be sent there for no start.
What if i was not marandized?
You cannot be sent to jail
How do you delete a message from facebook you sent so the user you sent it to doesnt get it?
If you have sent it then you cannot prevent the recipient receiving it.
How can you modified velocity of servomotor continously?
You can modify the velocity of a servomotor continuously by adjusting the pulse width modulation (PWM) signal sent to the motor driver. By changing the duty cycle of the PWM signal, you can control the average voltage supplied to the motor and thus adjust its speed dynamically. You can also use feedback mechanisms, such as encoders or sensors, to precisely adjust the motor velocity in real-time.
