answersLogoWhite

0

In a rectifier, a center-tapped transformer and two diodes can form a full-wave rectifier that allows both half-cycles of the AC waveform to contribute to the direct current, making it smoother than a half-wave rectifier. This form of circuit saves on rectifier diodes compared to a diode bridge, but has poorer utilization of the transformer windings.

User Avatar

Wiki User

12y ago

What else can I help you with?

Continue Learning about Movies & Television

Full wave rectifier using RC triggering circuit with diagram?

A full-wave rectifier (sometimes called a "bridge" rectifier) produces output current on both half-cycles of the input AC waveform. ******************************************** There are two types of full wave rectifier circuit. One uses four diodes in a "bridge"configuration and is fed from a simple transformer winding. The other uses two diodes and needs to be fed from a centre tapped transformer winding.


Why use half wave rectification and what are its advantages over full wave rectification?

A full-wave rectifier will provide an output through both the positive and negative halves of the AC sine wave. The half-wave rectifier will only provide an output for half the cycle. The filtered outputs of both rectifiers can be "smoothed" well, but the higher the load on the half-wave rectifier, the more the output voltage will vary across a cycle of input power. This results in higher ripple and makes regulation a bit more difficult. The full-wave rectifier will provide an output through both the positive and negative halves of the sine wave. It effectively "inverts" the negative half of the cycle and provides two "pulses" of power per cycle as opposed to one pulse per cycle for the half-wave rectifier. The full-wave rectifier might use a pair of diodes and a center tapped transformer, or might use four diodes in a full wave bridge configuration and a transformer with no center tap.


What is uses of tapped coil?

If question is about a transformer's tapped coil then the taps are a way of getting different voltages from one transformer. The end of the transformer's coil is the common point and the taps to this common point will give different voltages depending on where in the coil the taps are taken from.


What are the ratings and certificates for Tapped Out - 2003?

Tapped Out - 2003 is rated/received certificates of: USA:R


How add friends on simpsons tapped out?

When you go on requests click the + in the top corner then type either the email address or game centre name and click send

Related Questions

What is the advantages of using the bridge rectifier over the center tapped rectifier?

you only use half the number of windings in the bridge comparing it to the center tapped , and in the bridge rectifier the peak inverse voltage that a diode must be able to sustain without break down is half of that in the center tapped PIV per diode: center tapped: 2Vm : bridge : 1Vm


Why bridge rectifier is prefer over center type rectifier for low voltage applications?

there is no need of bulky centre tap in a bridge rectifier. TUF(transformer utilisation factor) is considerably high. output is not grounded. diodes of a bridge rectifier are readily available in market. *the PIV(peak inverse voltage) for diodes in a bridge rectifier are only halfof that for a centre tapped full wave rectifier,which is of great advantage.


Who is better among centre tapped rectifier and bridge rectifier?

It depends on what you're doing and what you have available. If you can find a good center tapped transformer with the target voltage, that will save you 2 diodes. If you're going for the "quick and dirty" solution and you don't have a center tapped transformer, a bridge rectifier is an excellent way to get dirty DC. ANSWER: The center tap will offer a .7 v advantage over the bridge. Be aware that power output does not change just the voltage increases


Is there any application where center tap rectifier is preferred over bridge rectifier?

For a center tapped full wave rectifier transformer secondary gives a voltage that is 2Vm. For a bridge rectifier it is Vm.


Why cant you implement centre tapped full wave rectifier without centre tapped transformer?

The center tapped full wave rectifier depends on two similar windings, each 180 degrees out of phase with respect to each other. You are only going to get that with a center tapped winding. Without the center tap, you need four diodes.


What is the basic difference between a full wave bridge rectifier and a full wave center tapped rectifier?

A full-wave bridge rectifier with 4 diodes gives a dc output voltage equal to the average voltage of the whole transformer secondary. A FW rectifier with 2 diodes and a centre-tapped secondary gives an output voltage equal to the average voltage of half the secondary. If you have a 12-0-12 transformer, the bridge gives a 24 v output, while the 2-diode FW rectifier gives 12 v (approximately).


Why to use four diodes when two diodes also can serve the purpose in bridge rectifier?

Four diode rectifier not require a center tapped transformer.


Why you are using the bridge rectifier in most of the circuits instead of full wave rectifier eventhough the output of both are same?

If diode in the bridge circuit becomes open the circuit will become a half wave rectifier instead, but if a diode in a full wave rectifier opens then the whole circuit becomes open. (No current flow). ************************************************************** The outputs of the bridge and the two-diode full wave rectifier are not the same. For the rectified voltage to be the same value, the two-diode full wave rectifier must be supplied from a centre tapped transformer winding, the total voltage of which is twice that necessary for the bridge rectifier circuit. Furthermore, the maximum d.c. which may be drawn from the centre tapped transformer/two-diode arrangement, assuming capacitive filtering, is the same value as the transformer secondary winding's capacity. In the case of the bridge, the maximum d.c. which may be drawn, also assuming capacitive filtering, is 62% of the transformer secondary winding's capacity.


Why can't we implement the center tapped full wave rectifier without center tapped transformer?

A center-tapped transformer and two diodes can form a full-wave rectifier that allows both half-cycles of the AC waveform to contribute to the direct current, making it smoother than a half-wave rectifier. This form of circuit saves on rectifier diodes compared to a diode bridge, but has poorer utilization of the transformer windings. Hence we do not use centre tapping for full wave rectification.Ashish sharmaAstt. ProfessorHIET, Shahpur, kangra(H.P.)


Full wave rectifier using RC triggering circuit with diagram?

A full-wave rectifier (sometimes called a "bridge" rectifier) produces output current on both half-cycles of the input AC waveform. ******************************************** There are two types of full wave rectifier circuit. One uses four diodes in a "bridge"configuration and is fed from a simple transformer winding. The other uses two diodes and needs to be fed from a centre tapped transformer winding.


Why bridge rectifier is prefer over center type rectifier?

it is more preferable over center tapped rectifiers because you dont have to use special centre tapped transformer that has larger secondary windings thereby reducing the size and cost it also has another advantage by the use of 4 diodes i.e. peak voltage sustained by each diode is half of that sustained by the diodes in center tapped system that uses only 2 diode. thus lifespan of bridge type rectifier is more.


Why a full wave rectifier is preferred over a half wave rectifier?

The a.c. component, or ripple, produced by the 4-diode (full wave) bridge rectifier is the same as that produced by the 2-diode full wave rectifier. The bridge is connected across the secondary winding of a transformer. The 2 diodes of the other type of full wave rectifier are each connected to one end of a winding, but that winding requires a center tap. For any desired value of d.c. after rectification, the a.c. voltage of the 2-diode rectifier winding has to be twice that of the winding required for the bridge.