No, the adapter's power output has to be equal to or greater that the current draw of the device.
The voltage would match but the amount of power would likely not be enough to run the device. Under-power will not likely harm the device, but it won't work correctly. Always use the correct voltage/power for your devices!
yes but the device will not work property or nor work at all <<>> No, the 100 mA adapter will be too small to operate a device that requires 300 mA for its operation. By trying to draw a higher current than the adapter can supply, the adapter will heat up and possibly burn itself open. In other words the adapter will stop working.
A: A DC adapter is basically like a battery except it is conditioned from an AC source. To change over measure the voltage when fully operational then switch to battery that have the same voltage as the adapter. the only concern should be the power required
The rule with power adapters is generally that the voltage must be the same as the device's input voltage requirements. However, the amperage just has to be equal to or greater than the device's input current requirements. The device will draw as much current as it needs. But, mismatching voltages can destroy electronic equipment.
Your question is confusing, but if you are asking whether you can use a 9V/250 mA adapter to supply a load device rated at 5 V/1000 mA, then the rule is quite straightforward. The adapter's rated output voltage must match that of the intended load, but its rated current must exceed that of the load. So in your example, you cannot use the adapter with the intended load.
No. The device will try to draw 700 milliamps which will overload the 300 milliamp adapter most likely causing it to burn out and possibly catch fire.
No, a power adapter must supply the same voltage, same polarity, and at least as much current as the load requires. Your adapter can only supply 300mA, which is less than the 700mA required by the load.Your game probably will not turn on and the power adapter may be damaged.
Yes, you can use a 300mA adapter on a 1A device, but it may not work properly or could damage the adapter. The device may draw more current than the adapter can provide, leading to insufficient power, potential overheating, or failure of the adapter. It's always best to use an adapter that meets or exceeds the device's current requirements for optimal performance and safety.
No, if the device needs 700mA of current, your power adapter cannot supply adequate current.
No, running two outdoor Kelkay Easy Fountains off one 12V-700mA adapter is not advisable. Each fountain typically requires a certain amount of power, and if both fountains exceed the 700mA limit, it could lead to insufficient power supply, causing malfunctions or damage to the fountains or the adapter. It's best to use a separate adapter for each fountain or ensure that their combined power requirements do not exceed the adapter's capacity.
Yes you can, however in an unusual situation (i.e. electrical fault in the device), the adapter will allow 5x the current the device is rated for to pass into that device. In normal operation, the device will draw what it needs, based on fans running or not, etc. Under these conditions, as long as the adapter puts out the proper Voltage, the device will operate just fine.
The device is compatible with a USB-C power adapter.
Yes, you can use a 300mA power supply in place of a 400mA supply, but it may not provide enough current for the device to operate properly. If the device requires 400mA and only receives 300mA, it may underperform, malfunction, or even be damaged due to insufficient power. It's important to ensure that the power supply meets or exceeds the current requirements of the device for safe and effective operation.
Most probably you are using a AC (117V or 220V) to DC 6V converter adapter. If yes, then the answer is no, you cannot use a lower current rating for a device that draws more current. If you plug in a device that needs DC 6V 500 mA to an adapter that can only supply DC 6V 300mA, then the adapter could start sending higher than 6 volts current which may damage your equipment or overheat the adapter. If you are using a higher mA rating adapter, then it's okay. For more technical details, see: http://www.jaycar.com.au/images_uploaded/plugpack.pdf
I think you mean to ask if one can use a 9v 600mA adapter to power a 9v 300mA appliance. Yes, you can do that. A 9v 600mA adapter will deliver 9v at up to 600mA. A mA is one milli amp, or one thousandth of an amp. 300mA is 300 thousandth of an amp, 300/1000 or 0.3 amps. 600mA is 600 thousandth of an amp, 600/1000 or 0.6 amps, and is twice the current of 300mA.
You would overload and damage the device and/or the adapter.
It is generally safe to run a 4.3V device with a 5V power adapter, as the device should only draw the amount of voltage it is designed for. However, there is a slight risk of damaging the device if the voltage is consistently higher than the recommended level.