0
Explain how to check that chips on a video card are properly seated in their sockets?
While properly grounded (to prevent static electricity buildup and damage to the electronic components) gently push downward on the chip.
Added 1 Dec 08:
Remove the card from the expansion slot and use a screwdriver to press down firmly on each corner of each socketed chip on the card. Chips sometimes loosen because of thermal changes; this condition is called chip creep.
pg. 422
What else can I help you with?
How do you check that chips on a video card are properly seated in?
Press down with a screw driver on all corners of the socketed chip on the card. This problem occurs because of thermal changes and is called chip creep.
Is Phil Collins ill?
Lately, I've noticed that Dr. Phil is not acting right. He seems confused and takes awhile to explain himself. It's not easy to explain. His older shows are on OWN. Check them out and compare his mannerism's to his current show, you'll see what I mean.
Rear tail light works but goes off when applying brakes on a 2000 grand Cherokee?
Replace the bulb. There are usually 2 filaments in each bulb and one is most likely out. Replacing it should solve the problem
How do you check fuse with multimeter?
The current in the socket can not checked directly because the sockets are connected in parallel to the supplu and we can not measure current in parallel it is always measure in series so connect a lod to socket after that use ammeter in series to measure electric current.
What is wrong when your interior and tail lights go out and put a new fuse in then they come on and go out again?
Overload or short to ground in circuit Remove all bulbs and check sockets, Replace buklbs one at a time until fuse blows to determine where problem exists Then investigate that area for bad socket or wire frayed to ground
What can you do if a computer constantly restarts but never boots up?
If you hear beeping, check the memory sticks to see if they are seated properly.
Every light on the rear end of your 86 cutlass won't work fuse is fine how can you fix this?
Check/replace bulbs Check light sockets for corrosion Check light sockets for power/ground - if none check wiring to sockets
What are the differences between e11 and e12 light bulb sockets?
The main difference between e11 and e12 light bulb sockets is their size. E11 sockets are smaller and have a diameter of 11mm, while E12 sockets are slightly larger with a diameter of 12mm. This means that E11 bulbs are not compatible with E12 sockets and vice versa. It is important to check the socket size before purchasing a light bulb to ensure it will fit properly.
Why dont The brake lights on my 1966 Mustang not work and I have already replaced the switch?
Check the bulbs- they are double filamented with the smaller for brake lights Check the fuse Check the sockets for power and ground Check the sockets for corrosion
All my stop lights signal lights and emergency lights on 1998 Ford E350 are not working.?
Check bulbs Check sockets for corrosion Check sockets for power and ground Check fuse for stop lights Check fuse for parking/tail lights
Why would a 1999 ford ranger blow oil out immediately onto exhaust pipe?
also check that oil filter has not "blown out " or gasket is not seated properly Check that oil sending unit is not defective and blowing oil out of the top
Why would my 1995 buick skylark lose brake lights or turn signals?
Check the bulbs - they are double filamented - smaller for stop/turn and larrger for tailights Check the sockets for corrosion Check the sockets for power /ground
How can I troubleshoot issues with my light switches and sockets?
To troubleshoot issues with light switches and sockets, first check if the circuit breaker is tripped. If not, inspect for loose connections or damaged wiring. Test the switch or socket with a voltage tester to see if it is functioning properly. If issues persist, consult a licensed electrician for further assistance.
Why is your fuse blowing when you hit the brakes?
Dead short to ground in one of the brake light sockets or wiring to them. Remove bulbs and check socket for corrosion or breakage and check for a bad wire to sockets
How do you Change Position Light on the Volvo S-60?
This usually means there is a bulb out, there is a bulb failing or there is a bulb that is not seated properly. Check the bulbs in the tail lights especially (there are a lot of them and you may not notice if one is out).
How do you check that chips on a video card are properly seated in?
Press down with a screw driver on all corners of the socketed chip on the card. This problem occurs because of thermal changes and is called chip creep.
Why is my 93 jeep hesitating after i have tuned it up?
You may have pulled out or ruptured a vacuum line. Also check that all spark plug wires are properly seated and correctly routed. New spark plugs do not always come pre-gapped - did you check the gap?
