0
Rear: Brake, Back-up, Tail, Turn signal (3 bulbs, all # 3157)
To access the rear bulbs, open the liftgate and remove the two Phillips head screws from the side of the housing as shown in the center photo above. Slowly and firmly rotate the assembly away from the vehicle until it disengages from the ball pin socket that secures it in back.
Each of the three light sockets, all containing the same exact bulb type, can be removed by turning them counter-clockwise 1/4 turn.
Taillight harness connector
To remove the taillight harness, slide the red lock tab up and pull connector off.
What else can I help you with?
You have 2004 Jeep Grand Cherokee Laredo brake and abs light is on how can you fix it?
How to change the brake switch on a 2004 Jeep grand Cherokee Laredo
Why stop lights will not work bulbs good no blown fuses Jeep Cherokee not a Grand or a Laredo?
brake relay or sensor
How do you change the Rear wheel bearings on a 1998 Grand Cherokee Laredo with rear disk brake also can't remove the Rotor rear?
See: http://autorepair.about.com/library/a/1i/bl841i.htm
Why does your 2001 Jeep Grand Cherokee Laredo steering vibrate when you apply the brakes?
Warped brake rotors. This is a very common problem for the 1999-2004 Grand Cherokees. You will need to have your rotors replaced, or resurfaced. The best resurface method is with an on car brake lathe.
What type brake fluid does a 2005 Jeep Grand Cherokee 5.7 liter engine take?
A 2005 Jeep Grand Cherokee uses DOT 3 fluid.
You have 2004 Jeep Grand Cherokee Laredo brake and abs light is on how can you fix it?
How to change the brake switch on a 2004 Jeep grand Cherokee Laredo
Brake repair on a 1996 grand Cherokee Laredo jeep?
Problem?
What fuse controls the brake lights on a 2000 Jeep Grand Cherokee Laredo?
my fuse panel (with the descriptions) is gone off of my 2000 jeep grand Cherokee Laredo, how to i get a description of what all 32 fuses control on my jeep?
How do you change rotors on a 1997 Jeep Grand Cherokee Laredo?
Remove the wheel; remove the brake pads and caliper; the rotor should slide off of the lug bolts.
How are the brake lights on a 1999 Jeep Grand Cherokee Laredo interwired with the headlamps?
They aren't. The brake light circuit is not connected with the headlight circuit.
Why stop lights will not work bulbs good no blown fuses Jeep Cherokee not a Grand or a Laredo?
brake relay or sensor
How do you change the Rear wheel bearings on a 1998 Grand Cherokee Laredo with rear disk brake also can't remove the Rotor rear?
See: http://autorepair.about.com/library/a/1i/bl841i.htm
What size torx bit is needed to remove 2000 grand Cherokee Laredo front brake caliper bolt?
I also have a 2000 grand Cherokee Laredo. Just changed front pads, and it is a torx bit T45. I couldn't find this answer on the web, so I bought several sizes to find out.
If you use p23575r-15tires on your 1998 jeep grand Cherokee Laredo will it effect the operation of the abs brake system?
Mine seems to work fine.
How do you change brake light switch on 93 Jeep Grand Cherokee?
The 1993 Jeep grand Cherokee brake light switch simply plugs in and out. The brake light switch is located beneath the dashboard on the drivers side of the engine compartment.
What would be causing a scrubbing noise in rear brakes when you already replaced brake pads in a 96 grand jeep Cherokee Laredo?
The brake pads might not be adjusted properly. The brake pads can be too tight and have contact with the rotors.
Why does your 2001 Jeep Grand Cherokee Laredo steering vibrate when you apply the brakes?
Warped brake rotors. This is a very common problem for the 1999-2004 Grand Cherokees. You will need to have your rotors replaced, or resurfaced. The best resurface method is with an on car brake lathe.
