0
How do you remove the inside door panel of a 2000 Jeep Cherokee Sport to replace the window motor After removing the screws the panel does not budge?
Wiki User
∙ 16y ago
That is a good answer. I would add a cautionery note that the snaps are flimsy and break easily. It it is the same as my 2001 Grand Cherokee there are plastic snaps along the perimeter of the door trim. You will neet to us a putty knife to start prying it away to snap the trim off. The best place to start is the bottom left corner and work your way around. Answer Go to this site for a detailed answer: http://www.wjjeeps.com/doors/doorpanel.htm
Wiki User
∙ 16y ago
Add your answer:
Earn +20 pts
Removing the entire headlight on a Jeep Grand Cherokee?
I'm trying to replace the headlight assembly for a 2000 Jeep Grand Cherokee Lerado. What bolts or screws do I remove
Can you get to the fuel pump in a 2001 Jeep Grand Cherokee Laredo from the inside of the truck?
No, you will need to remove the tank.
How do you replace the turn signal lever on grand Cherokee?
This link should help. http://www.jeepforum.com/forum/f140/how-2005-2009-grand-cherokee-wk-fog-light-install-867728/
Where is the valve body on a jeep grand Cherokee transmission?
The 1994 Jeep Grand Cherokee ERG solenoid is located on the firewall of the engine compartment. The solenoid will be on the passenger side of the firewall.
How do you replace the choke 1994 Jeep Cherokee Sport?
doesn't have a choke , but has an enrichener valve , remove the bolts that hold the valve ,take it out unplug & replace ,can be found near throttle body .
Removing the entire headlight on a Jeep Grand Cherokee?
I'm trying to replace the headlight assembly for a 2000 Jeep Grand Cherokee Lerado. What bolts or screws do I remove
Do you have to remove the radiator to replace the water pump on a 1988 Jeep Cherokee 4wd?
Probably not. What you will do is remove the fan first, and then the fan shroud. The reason for removing the shroud is so you have more room to work.
How do you replace slave cylinder tube without removing transmission?
It depends on where the slave cylinder is located. If it is inside the bell housing you will have to remove the transmission.
How do you replace headlight for 2008 Hyundai Sonata?
The headlight on your 2008 Hyundai can be removed by removing the headlight retaining bolts from the inside of the engine compartment. Remove the wiring harness and replace with a new headlight.
How do you replace a calliper on a 1999 Mazda?
remove the wheel,remove the brake line,removing the two bolts holding it on and then install opposite of removing.
How do you change the fuelpump on a 98 Cherokee?
ITS INSIDE THE FUEL TANK, YOU MIGHT HAVE TO DROP THE TANK, THE REST IS REAL EAST..REMOVE OLD REPLACE WITH NEW. HOPE THUS HRLPS
How do you replace a licence plate bulb on a Lincoln ls 2000?
Remove the trunck lid liner, with approiate retainer removing tool. Bulbs are accessed from inside lid.
How do you remove fuel tank on a 2000 Honda accord?
If you are removing the tank to replace the fuel pump stop. There is an access panel inside the car just above the fuel pump location. Remove that panel and you can get to the pump.
Do you need to remove radiator to replace grille on 91 Chevy pickup?
No, you can replace the grill without removing the radiator.
How do you replace a fuel pump on a 2001 Honda Accord?
There is an access panel above the fuel pump inside the car. Remove that panel and you can change the pump without removing the fuel tank.
How do you replace the inside drivers side door handle on a 2000 VW Beetle?
You can replace the inside drivers door handle by removing the door panel. With the door panel removed the door handle mechanism will be visible. Remove the linkage from the door handle. Remove the door handle retaining bolts. Reverse the process to install the new door handle.
How do you replace outside door handle 2000 mountaineer?
To install an exterior door handle on a Cherokee Jeep, first remove the window crank handle and the three screws in the inner door trim panel. Second, remove the inner door panel from the door using a trim stick and take off the vapor barrier inside the door. Third, remove the nut on the rear of the door handle, position the exterior door handle, and secure in place.
