0
Rear: Brake, Back-up, Tail, Turn signal (3 bulbs, all # 3157)
To access the rear bulbs, open the liftgate and remove the two Phillips head screws from the side of the housing as shown in the center photo above. Slowly and firmly rotate the assembly away from the vehicle until it disengages from the ball pin socket that secures it in back.
Each of the three light sockets, all containing the same exact bulb type, can be removed by turning them counter-clockwise 1/4 turn.
Taillight harness connector
To remove the taillight harness, slide the red lock tab up and pull connector off.
This worked for a 2004. I got it off some other q&a site.
What else can I help you with?
You have 2004 Jeep Grand Cherokee Laredo brake and abs light is on how can you fix it?
How to change the brake switch on a 2004 Jeep grand Cherokee Laredo
How do you replace the bulbs in the center console on a Jeep Cherokee Laredo?
I do not beleive your jeep uses bulbs in the console. I have a 2000 grand cherokee and it uses a light strip that is part of the console and can only be replaced with the shifter assembly....... I plan to cut the wires from the light strip and install a pep boys console light that uses replacable bulbs....probably will just lay it in there as long as it is protected and safe... Good luck
How do you reset the service interval on a 2008 Grand Cherokee Laredo?
To reset the oil change required light: turn key on, engine off; press gas pedal to the floor three times; cycle key.
How do you replace a Battery Temperature Sensor on a 1998 Jeep Grand Cherokee Laredo It is 4.0 liter Is it under the battery?
If you take out the battery tray and turn it over, you will find the Battery Temperature Sensor. Just found out this was the reason my check engine light stayed on. One of the wires was exposed and discharging to the frame of the jeep.
How do you replace the turn signal lever on grand Cherokee?
This link should help. http://www.jeepforum.com/forum/f140/how-2005-2009-grand-cherokee-wk-fog-light-install-867728/
You have 2004 Jeep Grand Cherokee Laredo brake and abs light is on how can you fix it?
How to change the brake switch on a 2004 Jeep grand Cherokee Laredo
How do you install passenger tail light kit for a 2004 Grand Cherokee Laredo?
How do you install passenger tail light kit for a 2004 grand cherokee?
How do you replace license plate light bulb on a 2000 Grand Cherokee Laredo?
Hard to see, but on my 96 Jeep Gr Cherokee there are two small screws next to each lamp on the outside.
How do you replace the shift console light for 1999 Jeep Grand Cherokee Laredo?
You can't. There's a circuit board connected to the shifter with LEDs on it. You have to replace the whole shifter. P/N # 52104149AC
Why would the check gage light go on in a 1996 grand Cherokee Laredo?
Because the oil is low.
What does check gauges and beeping mean on jeep grand Cherokee Laredo?
When there are beeping noises and the check gauges light on a Jeep Grand Cherokee Laredo it means there is a problem. The vehicle will need to be stopped and all of the fluids need to be checked immediately.
How do you reset the maintenance required light on a 1991 Jeep Cherokee Laredo?
Unplug or replace maint. timer
What does the light with the exclamation point mean on the 2008 jeep grand Cherokee Laredo?
parking break is on or low break fluid
How do you replace the stopbrake light bulb on a 2002 Jeep Grand Cherokee?
wjjeeps.com . they show how to replace every light and with what bulb
What is the timing on a 4.0 1998 Jeep Grand Cherokee Laredo?
The distributor is set to zero with a scan tool. It is not done with a timing light.
Rear light failure on 1994 Jeep Grand Cherokee?
Replace the bulbs
What does the yellow operation malfunction light indicate on a Jeep Grand Cherokee Laredo 2002?
The computer has detected a malfunction and set a trouble code.
