A little tricky compared to some others cars but not too bad.
1)Remove to Phillips screws from above the instrument cluster.
2)Pull out ash tray/change tray and remove two Phillips head screws behind that.
3)The entire dash piece is held in with several clips. Pull to remove very carefully, being sure to unplug all harnesses going to clock, dimmer switch, ect.
4)Remove screws securing radio and unplug.
Here is where you have a couple of options. If you have never done an install in an Elantra before, I recommend going to a Best Buy or antother car audio shop and get the proper mounting kit and wire harness. This makes the install quite quick and easy, and makes it look great. You can mount the radio with the factory brackets in place of the factory radio, but this can leave a gap with many aftermarket radios, unless the bracket is modified and redrilled to reposition the radio slightly.
In order to replace the scroll in a player piano you will need to locate the model number. Each piano model has different instructions as to ho to install the scroll.
Turn your car on, so that the radio can be turned on and off. Then turn your radio off. After is it off, push the clock button and while holding clock, use seek to change the hour and tune to change the minutes.
Nobody will ever replace Paul Gray because he was a great person but for their summer tour Slipknot are taking Donnie Steele.He's Slipknot's ex-guitar player and actually he is part of the family.....
Yes, it's a straight forward replacement. One in, one out.
That's not the easy part... At first i decide to do it by my self, after trying decide to pay someone... Ok. What you'll need - New Radio/Cd player & etc. New dash board kit (you could find one on ebay) Wires...(for me on this part problems starts...) To remove dash board you'll need only something what will go by the sides(i was using a knife) and press, that's all - these part is easy. Remove bolts disconnect father plug from old radio, antenna and be happy for a moment =) After find out that new radio kit wire have a lil bit different colours than yr car plug... The way i ind is to connect cable by cable according to old pins So check out the plugs mothers HYUNDAI (Model: A22004B) http://teletehnika.info/pins/files/hyundai-a22004b.jpg HYUNDAI (Model: H-245HPE) http://teletehnika.info/pins/files/hyundai-245-pinout.jpg so if you have working radio plug it connect close dash board - and be happy...
http://www.onlyforcars.com/amazing-6-2-car-dvd-player-with-gps-tv-for-hyundai-tucson-old-elantra-sonata-santa-fe.html It would help you .
If the Hyundai is a 1998 model, the related question should do the trick.
The fuse for the DVD player in a Hyundai Santa Fe is typically located in the fuse box under the dashboard on the driver's side or in the engine compartment. To find the specific fuse, refer to the owner's manual, which provides a diagram and description of the fuse layout. Look for a fuse labeled for the multimedia system or accessory power. If you suspect a blown fuse, check the corresponding fuse and replace it if necessary.
a scewdriver or hammer
The radio/CD player must NOT be turned on. Press the DISP button on the right-hand side until the the clock display starts flashing. Then press the Up or Down arrows to the left of the clock display to move the time forward or backward. These are the buttons you would use to change tracks or stations when the CD/radio is on. When done, press the DISP button again to stop the time from flashing.
noob
no you can n't
You can replace a cd player for a car by removing the old CD player after the vehicle has been turned off, there may be screws or clips to remove, unplug the cable, insert it into the new player and then put it back into the space provided.
There are many locations to buy a MP3 player to replace a walkman. The player can be found at Best Buy, Target and through the Apple store. They can also be found online through Amazon.
CD players are so relatively inexpensive today that it would be more cost efficient to replace a damaged in-dash player.
In order to replace the scroll in a player piano you will need to locate the model number. Each piano model has different instructions as to ho to install the scroll.
You either plug it in to the charger, or replace the battery.