0
Hot enough to melt solder onto electrical connections, and the skin off your finger.
Euan Russells answer: it can reach approximately 250 degrees, that is hot enough to burn your finger and possibly even leave a scar, so be careful and watch out!
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
Who is more popular iron maiden or Red Hot Chili Peppers?
Red Hot Chili Peppers
No clock or radio disply 2001 Mercury Villager but the CD changer and radio work just fine?
These radios are notorious for the displays going blank. I have a 1999 Villager Estate that had the same problem. The cause is usaully a set of large resistors on a circuit board inside the radio. The resistors get so hot that the solder connecting them to the circuit board actually melts and they become disconnected. The repair involves opening the radio, finding and resoldering the large resistors. They can be identified by the heat discoloration that they cause on the circuit board. This isn't too difficult, but if you have no experience using a soldering iron, then you may want to take the radio to a friend with a bit of soldering experience.
How do you fix onoff switch on guitar amps?
Open up your amp and see if there is loose wiring on your on/off switch. If so, you can take a soldering iron and fix it. If that doesn't work, or that's not the problem, then you can take it in to a guitar shop for a replacement switch, which will only cost you around $10.
Is iron maiden an antichrist band?
* Those that are not for Christ are against Him. You are either on one side of the fence or the other otherwises you will fall off. Hot or cold, not luke warm. Is Iron Maiden the AntiChrist? No they are not. Can they be anti Christian? Possibly. * No, Iron Maiden is not an anti-christian band.
Fill in the blank for the heavy metal band iron?
Iron Maiden. Iron Butterfly. Iron Monkey.
What is iron tin?
Tinning the Soldering iron is when the hot iron is coated with solder to aid in soldering and heat transfer
Why do you think it best for soldering iron to have its soldering stand?
why do you think its best for soldering iron to have soldering stand
What is soldering iron and how do you use it?
Soldering iron is used in heating the metal for soldering. If you want to learn more about soldering iron visit en.wikipedia.org/wiki/Soldering_iron.
Where can I go to get some information on soldering iron?
When you use a soldering iron you would be soldering some kind of metal frame or something because soldering irons are irrelevant to soldering iron. Sorry, not applicable.
Where do you place HOT soldering irons after use?
place the iron on its side(pointy part of the iron facing upwards)on the iron mat and let it cool
What is the definition of soldering stand?
soldering iron stand use for the electricians to easily the soldering iron make stand
How do you break in a new soldering iron?
Look at the 'bit', the part that gets hot that you do the soldering with. It should have an inclined flat surface on the end. If it has not, make one by using a file. Heat the soldering iron up. At the same time get the solder out, which should be tin solder with internal flux. When the iron is hot, quickly file the surface of the bit clean and apply the solder, which should immediately 'take' to the surface. That's it.
Why do you think it is best for a soldering iron to have a soldering stand?
Have you ever had a soldering iron roll off the table and land on your wrist, burning a hole that took over a month to heal? I did in 5th grade while building one of the Radio Shack electronics kits I had received for Christmas! Learning from that I made my own soldering stand from a small metal can and poured over a half inch of lead into the bottom from my lead soldier casting set to make sure that the weight of the soldering iron could not tilt the soldering stand!!! I was never going to run the risk of a soldering iron getting away from me again!!!!!
Characteristic of soldering iron?
Soldering iron is characterized by having the melting point of the filler metal.
Can you use an electric soldering iron on copper pipe and hobby tubing?
Rigid makes an electric soldering tool for soldering when an open flame is impractical like working in a hospital where there is flammable gases or Oxygen present.A regular type soldering iron may not get the fittings hot enough to allow for capillary attraction to draw the alloy into the fitting
What is the difference of a soldering iron and a soldering gun?
A soldering iron is a straight tool, sort of like a long screwdriver. A soldering gun actually looks like a gun or a drill.
What kind of tools are included in a soldering iron kit?
A soldering iron kit includes a soldering iron, a soldering iron stand, a sponge, diagonal cutters, long nose pliers as well as wire strippers. This example aplies only to sets for beginners.
