answersLogoWhite

0

Use a voltmeter with a high input impedance and measure at the source the voltage.

User Avatar

Wiki User

16y ago

What else can I help you with?

Continue Learning about Music & Radio

What unit is a Diode measured in?

Diodes are measured in terms of resistance. The formula is as follows Rd = Vd / Id. That is Resistance of the diode = voltage across the diode to current flowing throught the diode.


Should voltage going into home be 250V?

Its a bit on the high side, as measured between L1 and L2, but not a problem. Better for appliances than a low voltage. Lights will tend to be a just bit brighter and use a bit above rated power. Certainly a big problem if measured between either live conductors and the neutral.


What does Ohms mean for an amp?

Every amplifier has a high input impedance and a low output impedance. These electrical impedances extends the concept of resistance to AC circuits and are measured in ohms. In electronics, especially audio and sound recording, a high impedance bridging, voltage bridging, or simply bridging connection is one which maximizes transfer of a voltage signal to the load.


How do you calculate transformer voltage ratio test?

Secondary voltage / primary voltage


What is the Frequency response of common emitter amplifier?

The voltage gain is a measure of the amplified output available at the collector terminal divided by the voltage measured on the base. This if you have 10 mV applied to the base and voltage of 1 volt at the collector the voltage gain is 100ANSWERThe maximum voltage gain of a common emitter amplifier is dependant on the transistor itself. Some have only a very small voltage gain such as in Radio Frequency Power transistors. These are almost all used as common emitter circuits for bipolar transistors or common source for FETs.. On the other hand some darlington transistors can have common emitter gains of hundreds of thousands. If the stage has an unbypassed emitter resistor, the voltage gain is equal to Rload/RE, (Rload is the parallel value of the resistance from collector to the supply and the resistance of the load).If the emitter resistance is bypassed, the value of resistance to be used for RE is the internal Re which is equal to 25mV/Ie

Related Questions

Voltage is measured with?

Voltage is measured with a voltmeter.


What is the unit voltage is measured in?

ummm... ...voltage?


How voltage measured?

It is measured using a Voltmeter


How does the voltage measured across a dry cell ompare with the voltage drop measured across three bulbs in series?

The voltage measured across a dry cell is the total voltage output of the cell, typically around 1.5 volts. When three bulbs are connected in series, the total voltage drop across the bulbs will be the same as the voltage output of the dry cell. So, the voltage measured across the dry cell is equal to the voltage drop measured across the three bulbs in series.


If the resistance in ohms is higher than the voltage what does that mean?

Voltage is not measured in ohms. It is measured in volts.


The voltage measured directly across an open switch in a circuit will be?

The voltage measured across an open in a series circuit is the equivalent of the sourse voltage.


How do you make voltage?

Power (P) = Voltage (V) x Amperage (I) Written as P=VxI or to find Voltage V=P/I Voltage is measured in Volts (V) Amperage is measured in Amperes (Amps or A) Power is measured in Watts (W)


Why during measurement the measured voltage and currents have negative sign?

Because of the polarity of the circuit. The signs of measured current and voltage depends on the direction of the current and voltage.


How is electricty measured?

use voltage


Why is the measured voltage of a battery not the same as the stated voltage?

The measured voltage of a battery may not match the stated voltage due to internal resistance, temperature, or the age and condition of the battery. These factors can lead to voltage drops when the battery is in use.


What voltage is measured across an open fuse or switch?

The full circuit voltage


How can you tell the power and voltage when their is no current?

If there is no current, there is no power.The voltage can be measured with a voltmeter.