0
What does it entail to change the sway bar bushings and end links in a 1997 jeep Cherokee 4 wd?
Wiki User
∙ 12y ago
you will want to remove the stabilizer bar top link nuts making sure to note in what order they are assembled, (nut, washer, rubber bushung, etc). if you want to remove the links just unbolt then from the axle brackets. then take the stabilizer bar bracket bolts out and remove the bar from the Jeep. then pull the brackets off the stabilizer bar and replace them. just repeat in reverse order for instalitaion. Time allowed for a first timer would be 1 to 5 hours depending on front and rear both. Remember to secure the jeep with the proper safety precautions.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
Why is there rattling in my rear end in a 2001 jeep grand Cherokee?
Bad shock absorber.Bad/worn shock absorber bushings.Broken exhaust pipe/hanger.Bad/worn sway bar links or bushings.
How do you change the flasher relay on a 1999 grand Cherokee limited?
The flasher relay on a 1996 Jeep Grand Cherokee 318 by unplugging the old flasher and plugging in the new one. The flasher relay is located under the dash on the driver's side.
What were the social classes of the Cherokee Indians?
You mean what ARE the social classes of the Cherokee? They still exist, you know. The Eastern Band of Cherokee Indians, one of three federally recognized Cherokee tribes, lives closer to the old way than most other native tribes today. Their website might be a good starting point for you, try the links below.
How do you know if your sway bar is bad?
A sway bar is a bar of spring steel It is bad if cracked, broken or has notches or slots worn into it. Sway bar noise usually comes from worn links or worn bushings, both a relatively easy thing to repair.
Where can you find a Wiring diagram for 1997 Jeep Grand Cherokee?
www.Alldata.com (edited: is a link for a service you purchase. If you will be repairing you own vehicle as a hobby or are a professional, it looks good.)www.mitchel1.com (edited: is a links resource page to find other sites that may help.)
What is the name of the part at the end of the stabilizing bar?
link pins. bushings and links Stabilizer link bushings.
Why is there rattling in my rear end in a 2001 jeep grand Cherokee?
Bad shock absorber.Bad/worn shock absorber bushings.Broken exhaust pipe/hanger.Bad/worn sway bar links or bushings.
How do you change Sway bar bushing?
put a jack under front to relive tension and remove the two frame mounted bushings first then remove end links check all bushings and replace as needed i suggest using polyurathan bushings made by energy suspention
Can you grease an 2002 envoy front sway bar links?
They do not have grease fittings on the factory bushings or end links but after market greaseable polyurethane bushings and end links are out there at your local auto supply or Off Road store. The soft bushings and non grease end links that are installed from the factory are a bit too soft anyway and should be changed out. www.trailvoy.com - all the answers for your Trailblazer from true enthusiasts!
How do you learn Cherokee?
See the site below for links to websites where you can learn Cherokee.
How much should it cost to replace front bushings on a BMW?
I am having my strut bushings and sway bar links replaced for $330 in northern IL. NOT at the dealer. They wanted $800.
What auto parts are needed to repair the suspension on a vehicle?
Ball joints control arm bushings shock absorbers springs, coil or leaf sway bar end links and bushings
How do you repair noisy sway link bushings on 2003 ford focus SE?
Put new links in.
How do you replace sway bar?
You have to remove the end links, then remove the sway bar bushings (there are two) and the sway bar will come out. Sway Bars usually do not need to be replaced unless they are bend or completely broken. It is usually end links being worn or the bushings being warn out.
Why is my right front wheel making a tinkling sound?
You may want to check your sway bar links and bushings.
When should you replace worn rear sway bar links?
When the rubber bushings have deteriated and are no longer doing their job.
What if your 1995 jeep Cherokee xj 4X2 rumbles at any speed through the floor board while accelarating hard I changed the tranny mount and serviced the tranny I replaced the rearend with another used?
You may want to also look at your swaybar, the swaybar bushings, the swaybar links, the link bushings, the tie rods, and the wheel bearings - any one or combination of those could create a bad vibration at high speeds if faulty. I had to replace the swaybar links and bushings on my 95 GC Laredo to solve a similar issue. With the replacement of the rear end you might want to also be sure that the axle gears are properly aligned, free of dirt and debris, and well lubricated.
