0
To find the serial number on a Porter-Cable drill, check the bottom of the handle or the side of the motor housing, as these are common locations. It may also be located near the battery compartment or on a label attached to the drill. If you still can't locate it, refer to the user manual for specific guidance on your model.
What else can I help you with?
What electro house music video has a dancing horse?
the drill - the drill
What does Roc Drill mean?
In Army terminology, ROC Drill is a Rehearsal of Concept.
How do you drill 3 holes at one shot in pipes?
3 hole drill press `
How do you make an external antenna for your weather radio?
Take a like 8 metal coat hangers, make them all strait, then make them into v's, then get two wooden rectangle boards like 1x1 1/2 feet and cover them with aluminum foil, then drill 2 holes on one side and another two on the other side on both boards, then put the v's there and put washers on top of them and drill them in, then find copper wire and criss cross all of the v's and then connect it to a transformer and connect a coiaxial cable to ur reciever, then drill one whole at the bottom for the mast, then mount it in the direction of the transmitter. This should greatly improve reception!
Who are the girls in the tip drill video?
kk
What is a number drill?
a number of drill is the number that is most dived
Can a rotating masonry drill bit adjacent to a cable create a magnetic field and could it disrupt the electrical current within the cable?
No, a rotating masonry drill bit adjacent to a cable will not create a magnetic field and no it could not disrupt the electrical current within the cable .
Did Winchester ever factory drill Model 1894s for a receiver sight?
Yes, on certain models. Around serial number 1600000 and beyond.
How do you break into a sentry safe?
If you have the model and serial number you can write to Sentry Safe and they will give you the combination for a fee. The other option is to call a locksmith out, but they will drill the safe and cause damage beyond repair.
Should I get a cordless drill for a big job or is a cable the best?
the cordless will not have the max speed and effectivness for a huge job.the cable is most used these days and has a better power
What is the recommended number 6 drill bit size for drilling holes in metal?
The recommended drill bit size for drilling holes in metal is 3/16 inches, which is equivalent to a number 6 drill bit.
How do you put cable from battery through firewall in 1999 mercury sable?
Drill a hole and then insulate the hole with a rubber washer so the cable doesn't chafe on the jagged hole.
How can I attach a cable to a wall?
To attach a cable to a wall, you can use cable clips or hooks to secure the cable along the wall. First, determine the desired path for the cable and mark the locations where you want to attach it. Then, use a drill to create holes for the clips or hooks. Finally, insert the clips or hooks into the holes and secure the cable in place.
Is there anywhere to feed an amp cable through to the inside of the car from the battery on a 1999 mondeo 1.8 zetec?
You will have to drill a hole and feed the cable through that hole. Be sure and use a rubber grommet to prevent the cable from being cut.
How can I attach a cable to a wall securely?
To securely attach a cable to a wall, you can use cable clips or cable ties. First, determine the desired placement of the cable on the wall. Then, use a drill to create holes for the clips or ties. Insert the clips or ties into the holes and fasten the cable in place. Make sure the cable is snugly secured to the wall to prevent it from coming loose.
How to run coax cable from outside to inside of a building?
To run coax cable from outside to inside of a building, you will need to drill a hole through the wall where the cable will enter. Use a weatherproof cable entry point to protect the cable from the elements. Secure the cable along the exterior wall using cable clips. Inside, connect the coax cable to a wall plate or splitter to distribute the signal to your devices.
How is crude oil drill?
Drill oil wells is called cable-tool or percussion drilling. A hole is punched into the ground by a heavy cutting tool called a bit that is attached to a cable and pulley system. The cable hangs from the top of a four-legged framework tower called a derrick (The steel tower on a drilling rig or platform that is tall enough to store at least three lengths of 30-foot (9-meter) drill pipe.) The cable raises and drops the drill bit over and over again, shattering the rock into small pieces or cuttings. Periodically, those cuttings have to be wetted down and bailed out of the hole.
